FUTABA 14SG - Fail Safe Setting Procedure; Battery Fail Safe Setting Procedure; Battery Fail Safe Release Switch Setting

80
<Functions of Linkage Menu>
ŏ6HOHFWWKHIXQFWLRQ QDPH
DQGUHWXUQWRWKH/LQNDJH
PHQXE\WRXFKLQJWKH
RTNEXWWRQ 2UWKH 
HOME/EXITEXWWRQLV
SXVKHG
<SensorTouch™>
RETURN
FAIL SAFE
6HWVWKHVHUYRVRSHUDWLQJSRVLWLRQZKHQWUDQVPLWWHUVLJQDOVFDQQR
ORQJHUEHUHFHLYHGRUZKHQWKHUHFHLYHUEDWWHU\YROWDJHGURSV
(The display screen is an example. The
screen depends on the model type.)
The Failsafe function may be used to set up
positions that the servos move to in the case of
radio interference.
You may set either of two positions for each
channel: Hold, where the servo maintains its last
commanded position, or Failsafe, where each
servo moves to a predetermined position. You may
choose either mode for each channel. (FASST 7CH
mode: CH3 only)
The T14SG system also provides you with an
advanced battery monitoring function that warns
you when the receiver battery has only a little
power remaining. In this case, each servo is moved
to the defined failsafe position. (FASST 7CH
mode: CH3 only) The battery failsafe may be
released by operating a predefined control on the
transmitter (default is throttle), do not continue
to fly, land as soon as possible. Remember, if the
Fail safe setting procedure
0RYHWKHFXUVRUWRWKH)6LWHPRIWKH
FKDQQHO\RXZDQWWRVHWDQGWRXFKWKH571
EXWWRQWRVZLWFKWRWKHGDWDLQSXWPRGH
6HOHFWWKH)6PRGHE\VFUROOLQJWKH WRXFK
VHQVRU$FRQÀUPDWLRQPHVVDJHDSSHDUV
*The display blinks.
7RXFKWKH571EXWWRQ7RXFKWKH6EXWWRQ
WRVWRSVHWWLQJ
*The channel switches to the F/S mode.
0RYHWKHFXUVRUWRWKH326LWHP
 +ROGWKHFRUUHVSRQGLQJVWLFNNQREVOLGHU
HWFLQWKHSRVLWLRQ\RXZDQWWKHVHUYR
WRPRYHWRZKHQWKHIDLOVDIHIXQFWLRQLV
DFWLYDWHGDQG7RXFKWKH571EXWWRQIRURQH
VHFRQG
*The set position is displayed in percentage.
*If you want to return that channel to the hold mode, move
the cursor to the "F/S" item and touch the RTN button
to switch to the data input mode. Select the F/S mode by
VFUROOLQJWKHWRXFKVHQVRU$FRQ¿UPDWLRQPHVVDJHDSSHDUV
and then change the mode by touching the RTN button.
predefined control suddenly moves to a position
you did not command, land at once and check your
receiver battery.
'H¿QHVVHUYRSRVLWLRQZKHQVLJQDOVDUHORVWDQG
when receiver battery voltage becomes low.
:DUQLQJ
For safety, always set the fail safe functions.
Ɣ5HPHPEHUWRVHWWKHWKURWWOHFKDQQHOIDLOVDIHIXQFWLRQVRWKDW
the servo moves to the maximum slow side for airplanes and
to the slow side from the hovering position for helicopters.
Crashing of the model at full high when normal radio waves
cannot be received due to interference, etc., is very dangerous.
Ɣ,IWKHEDWWHU\IDLOVDIHLVUHVHWE\WKHWKURWWOHVWLFNLWPD\
be mistaken for an engine malfunction and will be reset at
WKURWWOHVORZDQGWKHPRGHOZLOOFRQWLQXHWRÀ\,I\RXKDYH
any doubts, immediately land.
Battery fail safe setting procedure
 %DWWHU\IDLOVDIHFDQEHVHWIRUHDFKFKDQQHO
E\WKHVDPHPHWKRGDVWKHIDLOVDIHVHWWLQJ
SURFHGXUH6HOHFWDQGVHWWKH%)6LWHP
 >21@%DWWHU\IDLOVDIHIXQFWLRQ21
 >2))@%DWWHU\IDLOVDIHIXQFWLRQ2))
Battery fail safe release switch setting
 7KLVIXQFWLRQWHPSRUDULO\UHOHDVHVWKHEDWWHU\
IDLOVDIHIXQFWLRQVRWKHIXVHODJHFDQ
UHFRYHUDIWHUWKHEDWWHU\IDLOVDIHIXQFWLRQ
ZDVDFWLYDWHGE\DGURSLQWKHUHFHLYHU
EDWWHU\YROWDJH7KLVVHWWLQJVHOHFWVWKHVZLWFK
ZKLFKUHOHDVHVWKHEDWWHU\IDLOVDIHIXQFWLRQ
0RYHWKHFXUVRUWRWKH>5(/($6(%)6@LWHPLQ
WKHVHWXSVFUHHQODVWSDJH
7RXFKWKH571EXWWRQ
*The switch selection screen is called.
*For a detailed description of the switch selection and ON/
OFF direction setting method, see [Switch Setting Method]
at the back of this manual.
ŏ6HOHFW>)$,/6$)(@LQWKH/LQNDJHPHQXDQGDFFHVV
WKHVHWXSVFUHHQVKRZQEHORZE\WRXFKLQJWKH
571EXWWRQ
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH