FUTABA 14SG - Thr Cut - Throttle Cut; Designating a Throttle Cut Setting Position (Helicopter)

83
<Functions of Linkage Menu>
ŏ6HOHFWWKHIXQFWLRQ QDPH
DQGUHWXUQWRWKH/LQNDJH
PHQXE\WRXFKLQJWKH
RTNEXWWRQ 2UWKH 
HOME/EXITEXWWRQLV
SXVKHG
<SensorTouch™>
RETURN
THR CUT
6WRSVWKHHQJLQHVDIHO\DQGHDVLO\DLUSODQHDQGKHOLFRSWHURQO\
Throttle cut provides an easy way to stop the
engine. Generally speaking, modelers will do so
E\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFNDWLGOH
The action is not functional at high throttle to
avoid accidental dead stick landings. The switch’s
location and direction must be chosen, as it defaults
to NULL.
Individually adjust the Throttle Cut activation
setting for each condition. (helicopter)
Throttle cut setting procedure
$FWLYDWHWKHIXQFWLRQ
 0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGWRXFK
WKH571EXWWRQWRVZLWFKWRWKHGDWDLQSXW
PRGH
 6HOHFWWKH$&7PRGHE\VFUROOLQJWKHWRXFK
VHQVRU
*The display blinks.
 7RXFKWKH571EXWWRQWRDFWLYDWHWKH
IXQFWLRQDQGUHWXUQWRWKHFXUVRUPRGH
6ZLWFKVHOHFWLRQ
 0RYHWKHFXUVRUWRWKH>6:@LWHPDQGDFFHVV
WKHVZLWFKVHWXSVFUHHQE\WRXFKLQJWKH
571EXWWRQDQGVHOHFWWKHVZLWFKDQG21
GLUHFWLRQ
*For a detailed description of the setting method, see [Switch
Setting Method] at the back of this manual.
7KURWWOHFXWSRVLWLRQVHWWLQJ
 0RYHWKHFXUVRUWRWKH>326@LWHPDQGWRXFK
WKH571EXWWRQWRVZLWFKWRWKHGDWDLQSXW
PRGH
 $GMXVWWKHVHUYRRSHUDWLRQSRVLWLRQDWWKURWWOH
FXWRSHUDWLRQE\VFUROOLQJWKHWRXFKVHQVRU
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is touched for one second, the servo
operation position is reset to the initial value.)
 7RXFKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
DQGUHWXUQWRWKHFXUVRUPRGH
*With the selected cut switch ON and the throttle stick at idle;
adjust the rate until the engine consistently cuts off.
However, be sure that the throttle linkage is not pulled too
tight or unreasonable force is not applied to the servo.
Designating a Throttle Cut setting position.
(helicopter)
*A throttle cut function acts in the low side of the throttle
position.
*"THRO" setting is common with all condition.
:DUQLQJ
Normal setting is slightly above idle.
7RDGGWKH7KURWWOH&XWSRVLWLRQXVHWKH
FXUVRUWRVHOHFWWKH7+52SHUFHQWDJH
GHVLUHGWKHQSUHVVDQGKROGWKH571EXWWRQ
IRURQHVHFRQG
*Since conditions are not offered when an Airplane is selected,
the Throttle Cut options will vary from the options noted
below.
*The Throttle Cut POS and SW settings are utilized for all
conditions.
*If the Throttle Cut switch is activated, or on, this status will
continue even if the condition is changed to an inhibited
setting.
*If the condition is inhibited (INH) the Throttle Cut is off if
the SW is in the off position and the throttle stick is low.
ŏ6HOHFW>7+5&87@LQWKH/LQNDJHPHQXDQGDFFHVV
WKHVHWXSVFUHHQVKRZQEHORZE\WRXFKLQJWKH
571EXWWRQ
ŏ&XUUHQWWKURWWOHSRVLWLRQ
ŏ,QGLYLGXDOO\DGMXVWWKH7KURWWOH&XWDFWLYDWLRQ
VHWWLQJIRUHDFKFRQGLWLRQKHOLFRSWHU
ŏ&XWSRVLWLRQ
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7KURWWOH
FXWVWDWXV
ŏ7KURWWOH
FXWVWDWXV
ŏ7KURWWOH
VWLFNSRVLWLRQ