To Next PageTo Next PageWhy does my GE Interlogix Concord Security System touchpad indicate 'Invalid' when bypassing a sensor?
If your GE Interlogix Security System touchpad indicates 'Invalid' or you hear 'Invalid' when attempting to bypass a sensor, it could be due to these reasons: You might be trying to bypass a 24-hour sensor that cannot be bypassed, such as group 26 fire sensors. Alternatively, the sensor may not be active in the current arming level.
How to fix no incoming AC voltage at GE Interlogix Concord Security System panel terminals 1 and 2?
If there's no incoming AC voltage at panel terminals 1 and 2 of your GE Interlogix Security System, follow these steps: Unplug the AC power transformer and disconnect the wires from both the transformer and the panel. Check the transformer-to-panel wire for any short or open circuits. Then, plug in the transformer and check for 24 VAC at the transformer's unconnected terminals. If you measure zero (0) volts, replace the transformer.
What to do if central station is not receiving reports from GE Interlogix Concord?
If the central station or pager isn't receiving reports from your GE Interlogix Security System: First, check that the premises phone line is working. Second, perform a phone test.
Why does my GE Interlogix Security System protest and won’t arm?
If your GE Interlogix Security System protests and won’t arm, consider the following: If you are arming to level 2, ensure all monitored perimeter doors and windows are closed. If arming to level 3, ensure all perimeter and interior sensors are closed.
What to do if installer cannot remember GE Interlogix Security System install code?
If the installer can't remember the install code for the GE Interlogix Security System: First, check your records to see if you have the install code on file. You can also verify the install code using the Downloader. Alternatively, use the Dealer Code to enter program mode and view the installer code.
What to do if my GE Interlogix Concord Security System won’t disarm?
If your GE Interlogix Security System won't disarm, consider these possibilities: You might be entering the incorrect code, so make sure you're using the right one. It's also possible that the access code you're using isn't programmed or set up in the user programming to disarm the system.
What to do if I forgot my GE Interlogix Concord access code?
If you've forgotten your access code for the GE Interlogix Security System, here's what you can do: First, check your personal records to see if you have the access code on file. You can also verify the access code using the Downloader. If all else fails, clear the memory and reprogram the panel locally.
How to troubleshoot GE Interlogix Concord when the panel does not power up?
If your GE Interlogix Security System panel isn't powering up and the touchpads aren't displaying or responding, try the following: 1. Ensure the panel transformer is plugged into an unswitched outlet. 2. Check the AC circuit breaker to confirm the circuit is live. 3. Verify the backup battery is correctly installed and the AC power transformer is plugged in. 4. Check the panel and transformer wiring for any issues. 5. Measure the incoming AC voltage at panel terminals 1 and 2; it should be approximately 24 VAC.
General| Brand | GE Interlogix |
|---|---|
| Model | Concord Security System |
| Category | Security System |
| Language | English |
Requirements dictated by codes, insurance, or Underwriter's Laboratories (UL).
Describes the requirements for UL Listed installations.
Describes the basic panel hardware capabilities out-of-box.
Guidelines for selecting the central panel location.
Procedure for mounting the panel to a wall or wall studs.
Grounding the panel and installing Power Line Carrier/Phone Supervision cards.
Allows installation of one SnapCard to expand panel functionality.
Typical wiring for N/C and N/O door/window intrusion detection and motion detectors.
Details for connecting 2-wire and 4-wire smoke detectors to zone input 8.
Connecting speakers, piezo sirens, and supervised wireless sirens to the panel.
Installing RF Receiver, Phone Interface/Voice Module, and other SuperBus modules.
Guidelines for installing an RJ-31X phone jack and connecting the phone line.
Connects the transformer and applies AC/battery power to the panel.
Procedures to enter the system's installer/dealer programming mode.
Guides through the first tier of system programming menus.
Setting essential codes for system access and programming.
Configuring central station reporting, phone numbers, and report formats.
Setting time-based features like RF Tx Timeout and Phone Test Frequency.
Sets time frames for light control and opening/closing reports.
Tests sensors and zones after installation or programming changes.
Checks panel communication with central station/pager.
Troubleshoots problems related to the panel not powering up.
Troubleshoots wireless sensor response or trouble conditions.
Lists part numbers and descriptions for wireless devices.
Details characteristics of different sensor groups.
