What to do if no system is found when starting up UNICORN on GE AKTAprocess?
If no system is found when starting up UNICORN, ensure the system is switched on. Check the communication cable and connectors. Reboot the PC: shut down Windows, switch off the SYSTEM POWER SWITCH, wait at least 5 seconds, and then restart the system.
What to do if pump is not working in GE AKTAprocess?
If the pump is not working, check if the emergency button has been pressed. Also, verify the air supply pressure and adjust it if needed. Inspect the method and valves. Try entering Pump:ManFlow > 1%. If the issue persists, contact GE Healthcare service personnel.
How to troubleshoot blockage or partial blockage of flow path in GE AKTAprocess?
If there is a blockage or partial blockage of the flow path, flush through to clear the blockage.
What to do if the actual flow rate deviates from the displayed flow rate on GE AKTAprocess Laboratory Equipment?
If the actual flow rate deviates from the displayed flow rate, or a flow rate is displayed when the pumps are off, this can be caused by changes in running conditions. Perform a zero-point adjustment of the flow meter to resolve this.
How to fix noisy UV-signal, signal drift or instability in GE AKTAprocess?
Noisy UV-signal, signal drift, or instability can be caused by bad UV fiber connections. Check the connections of the UV cell optical fiber and replace them if necessary.
How to fix compressed air failure during a run in GE Laboratory Equipment?
If there is a compressed air failure during a run, it may be caused by insufficient air pressure due to malfunctioning air supply equipment or a leaking air hose. Rectify the air supply problem and restart the run by pressing the Continue button.
What to do if there is too high outlet pressure in GE AKTAprocess Laboratory Equipment?
If there's too high outlet pressure, verify that the connected outlet is actually in use and that outlet containers are not placed too high relative to the pump. Inspect the tubing to the outlet container for excessive length, small internal diameter, narrow sections, or blockages. Also, check for any non-functioning valves or a malfunctioning valve at the container battery limit.
What to do if there is little or no flow in GE Laboratory Equipment?
If you experience little or no flow, check that the connected inlet is actually in use. Ensure inlet containers are not placed too low relative to the pump. Verify that there is liquid supplied to the pump. Also, check the tubing from the inlet container for issues like excessive length, small internal diameter, narrow sections, or blockages. A malfunctioning valve at the container battery limit could also be the cause.
What to do if there is erratic flow, noisy baseline signal, or irregular pressure trace in GE Laboratory Equipment?
Erratic flow, a noisy baseline signal, or an irregular pressure trace can be caused by gas bubbles passing through or trapped in the pump. Ensure there is a sufficient supply of liquid and check all connections for leaks.
What to do if the alarm 'Valve error' is displayed on GE AKTAprocess?
If the 'Valve error' alarm is displayed, perform a valve calibration. If the calibration doesn't restore the valve function, contact your local GE Healthcare representative. Note that if the 'Valve error' alarm is accompanied by 'No air supply to the system', the alarm is caused by a compressed air failure.
Defines the manual's purpose, scope, and typographical conventions.
Crucial information before operating, intended use, and prerequisites for safe use.
Details manufacturing, CE, international, additional, and environmental compliance.
Covers general, personal, installation, power, and operational safety measures.
Explains the meaning of various system and safety labels found on the equipment.
Details steps for emergency shutdown, power failure response, and system restart.
Summarizes standard/optional components, tubing, and cabinet types.
Provides front and rear views of standard and optional system configurations.
Details on structural, control, inlets/outlets, meters, pump, air trap, and valves.
Describes software modules, workflow, manual instructions, indicators, and alarms.
Details requirements for space, floor load, ambient environment, power, and air supply.
Provides guidelines for transporting the system in crate and when unpacked.
Covers assembly, control system setup, connections, and column connection procedures.
Details power requirements, UPS, grounding, circuit breakers, and cable specifications.
Steps for starting system/software, preparing components, testing, and final checks.
Instructions for starting, monitoring, and ending a system run.
Procedures for safely shutting down the system and the UNICORN software.
Lists weekly, monthly, and annual maintenance tasks for system components.
Procedures and recommendations for cleaning, including CIP and sanitization.
Provides procedures for short-term and long-term storage of the system.
Details required equipment and steps for calibrating the pH probe.
Addresses common system problems like PC connection and power failure.
Troubleshooting for pump not working, low flow, or high outlet pressure.
Symptoms and corrective actions for issues with UV signals or drift.
Contains general technical data, cabinet/system specs, and temperature/pressure limits.
Lists allowed exposure times and concentrations for various chemicals.
Provides an example UNICORN method for system cleaning procedures.
General| Brand | GE |
|---|---|
| Model | AKTAprocess |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
