GE F35 - Page 675

INDEX
F35 MULTIPLE FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL ix
Neutral IOC
FlexLogic operands .......................................................................5-209
logic diagram ...................................................................................5-240
settings ...............................................................................................5-239
specifications ......................................................................................2-18
Neutral overvoltage
FlexLogic operands .......................................................................5-209
logic diagram ...................................................................................5-254
settings ...............................................................................................5-253
specifications ......................................................................................2-20
Neutral TOC
FlexLogic operands .......................................................................5-209
logic diagram ...................................................................................5-239
settings ...............................................................................................5-238
specifications ......................................................................................2-18
Non-volatile latches
FlexLogic operands .......................................................................5-209
settings ...............................................................................................5-226
specifications ......................................................................................2-22
NOR gate explained ...........................................................................4-84
NOT gate explained ............................................................................4-84
O
Obtain list of port numbers ............................................................5-44
One-shot
error compiling in Engineer ..........................................................4-71
FlexLogic operators ......................................................................5-215
Operating temperature ....................................................................2-32
Operating times ....................................................................................2-18
Operator command to force logoff ............................................. 7-4
OR gate explained ...............................................................................4-84
Order codes .............................................................................................. 2-6
actual values .......................................................................................6-27
update ..........................................................................................3-61, 7-3
Oscillatory transient testing specifications ..........................2-33
Oscillography
actual values .......................................................................................6-26
clearing ........................................................................................5-39, 7-2
settings ...............................................................................................5-152
specifications ......................................................................................2-23
via EnerVista software ..................................................................... 4-2
Out of service ........................................................................................... 5-1
Outputs
contact outputs ..............................................................................5-312
control power specifications .......................................................2-28
critical failure relay specifications ............................................2-28
Fast form-C relay specifications ................................................2-28
Form-A relay ...........................................................................2-27, 3-16
Form-C relay .......................................................................................3-16
Form-C relay specifications .........................................................2-28
latching output specifications ....................................................2-27
latching outputs .............................................................................5-313
virtual outputs .................................................................................5-315
Overcurrent curve types ...............................................................5-228
Overcurrent curves
FlexCurves .........................................................................................5-233
IAC .........................................................................................................5-231
IEC .........................................................................................................5-230
Overfrequency
testing .......................................................................................................8-1
Overvoltage
auxiliary ..................................................................................2-20, 5-255
neutral .....................................................................................2-20, 5-253
phase ........................................................................2-19, 5-210, 5-252
P
Panel cutout .....................................................................................3-2, 3-5
Parallel Redundancy Protocol
actual values ......................................................................................6-11
explained ..............................................................................................5-46
settings .................................................................................................5-44
specifications .....................................................................................2-30
Parity ..........................................................................................................5-41
Part numbering .......................................................................................2-6
Passwords
authentication by device or server ..........................................5-15
bypass authentication ................................................................... 5-22
change ..................................................................................................4-60
change after installation ..............................................................3-66
change does not take relay out of service ..............................5-1
command .......................................................................4-61, 5-9, 5-10
default ...................................................................................................5-13
explained .................................................................................................2-3
FlexLogic operands .......................................................................5-213
lockout .......................................................................................4-62, 5-13
lost password ........................................................................................5-7
requirements .........................................................................................5-8
reset to factory defaults ..................................................................5-7
rules ...........................................................................................................5-8
settings ............................................................................4-61, 5-9, 5-10
settings templates ..............................................................................4-7
wrong entry ........................................................................................4-62
Permissive functions .......................................................................5-250
Per-unit quantity ....................................................................................5-4
Phase angle metering ......................................................................6-13
Phase current metering ..................................................................6-16
Phase IOC
FlexLogic operands .......................................................................5-209
logic diagram ...................................................................................5-237
settings ...............................................................................................5-236
specifications .....................................................................................2-18
Phase overvoltage
FlexLogic operands .......................................................................5-210
logic diagram ...................................................................................5-253
settings ...............................................................................................5-252
specifications .....................................................................................2-19
Phase rotation ....................................................................................5-182