GSE 672 - Chapter 11: Troubleshooting

To Next Page

To Previous Page

Model 672/675 Technical Reference Manual

11-1

Chapter 11 : TROUBLESHOOTING

This section describes all error codes generated by the Model 672 and Model 675. Most error codes show a

two-digit code reference along with a short text message. Possible causes and remedies are described for

each error.

Main Page

Default Chapter4
- Table of Contents4
Chapter 1: Introduction16
- Standard Features17
- Explanation of Symbols17
- Specifications18
- Enclosure19
- Display21
- Keypad22
- Rear Panel24
  - Model 67524
Chapter 2 : Option Installation28
- Rechargeable Battery Option Installation29
- Installation Instructions29
- External Battery Charger30
- Battery Status Icons31
- Non-Rechargeable Battery Installation32
- Third Scale Option34
- Fourth Scale35
- Setup Parameters36
- A/D Calibration36
- Scale Calibration37
- Weigh Mode Operation37
- Communication37
  - Ethernet Interface Module37
  - Module (Model 675 Only)40
- Ma Current Loop Operation (675 Only)43
- Database Option44
- Analog Output Option (Model 675 Only)64
- Reflash Software73
Chapter 3 : Application Setup74
- Model 67275
- Model 67584
- Setup Mode94
Chapter 4 : Operation130
- Basic Weigh (Model 672)131
  - Sample and Count131
- Quick Count (Model 675)132
  - Sample and Count132
  - Sample and Count133
- Counting Operation135
- Weigh Mode Operation139
Chapter 5 : Calibration146
- Quick Calibration147
- Remote Scale Calibration152
- Calibration Units152
- Mutli-Point Linearization153
- A/D Calibration153
  - Restoring A/D Calibration Values155
  - Entering A/D Calibration Values155
- Restoring the Calibrated Zero Reference156
Chapter 6 : Legal for Trade158
- NTEP Custom Setup159
- OIML Requirements163
- Data Storage Device (DSD)164
Chapter 7 : Operating Parameters172
- Parameter Instances173
- Accessing Operating Parameters174
- Mode Menu Access176
- Macro Access177
- Renaming Operating Parameters177
  - Renaming Parameters in the Setup Mode177
  - Renaming Parameters with Macros178
- Weight Parameters178
- Accumulation Parameters179
- Time & Date181
  - Time / Date (Mode 11)181
- Weight Averaging Parameters182
- Rate Parameters184
- Counting Parameters186
- Remote Scale Parameters188
- Extended Weight Parameters189
  - DSD Parameters (Parameters 64.1 - 64.9)190
- Setpoint Timers191
- Random Number191
  - Random Number (Parameter 79)191
- Variables192
  - Variable Types (P80)192
- Independent Timers197
  - Timer Ticks (Mode 81)198
  - Timer Seconds (Mode 82)198
- Prompting Parameters198
- Diagnostic Weight Parameters202
Chapter 8 : Communiction204
- Communication Port Connections205
- Communication Port Setup Parameters205
- Receive Operations205
  - Receive Buffer205
  - Macro Language206
- Custom Transmit209
- Transmitting Display Data220
- Modbus ™ Communications221
- Checksum Protocol226
- Transmit Network Address (ASCII)230
- Printing Operations231
- Input Interpreter231
- Ethernet (Option)238
Chapter 9 : Macros240
- Macro Setup241
- Invoking Macros246
- Macro Execution248
- Enable/Disable Comm Port256
- Select Comm Port261
- Record Received Serial Data264
- Clear Receive Buffer267
- Record A/D Data268
  - Averaging270
- Motion Delay270
- Perform Scale Specific Function271
A%. Audit Trail272
B%. Database Option Battery273
- If Macro Interrupted274
  - Save/Restore Entry Buffer275
  - Set Pause Time276
Activate Setpoint276
- Activate Setpoint277
B Break Macro279
C Draw Box / Line on 8X40 and 16X40 LCD282
C Place a Fixed Image on LCD284
C Animate Images on LCD290
D Deactivate Setpoint293
E End if295
F if Setpoint Deactivated295
G Get Entry296
H Redefine Comm Port Function297
- Redefine Comm Port Function298
I Refresh Display299
J Jump to Tag299
Get Entry from 8X40 and 16X40 LCD300
- Jump to Tag300
If Entry Terminated by Function Key302
L Language Selection303
M Mode Selection304
N else (if Not)305
O if Setpoint Activated305
P Pause306
Q Send Custom Transmit306
- Send Custom Transmit307
R Rename Mode309
S Sound Beeper310
T Tag Position311
- Tag Position312
Wait for Keypress313
Request Display Data314
Y if Yes (Enter)314
- Save Entry Buffer315
- If no Entry315
  - If Yes315
- Restore Entry Buffer316
  - Call / Go to Macro316
  - If Database Error317
- Scale Select318
Target Accuracy319
Perform Sample320
Clear Entry Buffer321
Display Control321
Enter / Sample326
If Parameter Preset327
- Enter / Sample327
If Key/Remote Key Held329
Alpha Mode330
Digital Filter331
Modify String332
Get Numeric Entry334
Math Assignment335
Math Comparison342
String Concatenation343
Print345
Enable RS-485 Transmitter345
A/D Interval346
Select Mode348
Tare348
Units350
Write Value to FRAM351
DSD Database Functions352
Recall Row356
Update Row357
Make Row357
Print Database358
First / Last Row359
Next Match361
Delete Row362
Clear Column362
Clear Database363
Set Database363
Set Column363
Download364
Print Row366
Print Database Errors367
Upload New367
Upload Update368
Sort Database369
Database Auto Test370
Database Show Links370
Zero371
- Start Group373
  - End Group373
- Boolean Logic374
  - The "If" Statement374
- Pointers380
  - Variable Pointers380
  - Non-Variable Pointers381
- Interrupt Macros382
  - Invoking an Interrupt Macro382
- Macro Debug383
  - Reviewing the Macro Debug Table384
Chapter 10 : Information Parameters388
- Accessing Information Parameters389
  - Navigating Information Parameters389
  - Exiting Information Parameters389
- Memory Parameters390
Chapter 11 : Troubleshooting404
Error Messages405
- Hardware Error Codes406
- General Error Codes407
- Macro Error Codes409

Other manuals for GSE 672

User Guide48 pages

Related product manuals

GSE 672 - Chapter 11: Troubleshooting

Table of Contents

Other manuals for GSE 672

Related product manuals