HEIDENHAIN TNC 320 - Page 722

Index
722
HEIDENHAIN | TNC 320 | ISO Programming User's Manual | 10/2017
Pre-positioning..................... 250
PDF Viewer.............................. 159
PLANE function................ 479, 481
Automatic positioning.......... 499
Axis angle definition............. 496
Euler angle definition........... 488
Incremental definition.......... 495
Overview............................. 481
Point definition..................... 493
Positioning behavior............. 498
Projection angle definition.... 486
Resetting............................ 483
Selection of possible
solutions.............................. 502
Spatial angle definition......... 484
Vector definition................... 490
Plan view................................. 592
PLC and NC synchronization.... 393
Pocket table............................. 219
Polar coordinates...................... 125
Fundamentals...................... 125
Programming....................... 274
Positioning................................ 580
With Manual Data Input....... 580
With tilted working plane..... 431
Presets
managing............................. 531
Preset table...................... 531, 531
transferring probed values.... 548
Principal axes........................... 125
Printing messages.................... 362
Probing
With end mill....................... 538
Probing a plane........................ 559
Probing cycles.......................... 541
Manual operating mode...... 541
Probing values
writing to the preset table.... 548
Probing with a 3-D touch probe 540
Processing DXF data
Basic settings....................... 299
Filter for hole positions........ 314
Selecting a contour.............. 307
Selecting machining positions....
310
Setting layers....................... 301
Selecting hole positions
Single selection.................... 311
Program.................................... 128
Opening a new program...... 132
Structure.............................. 128
Structuring........................... 179
Program call
Any desired NC program as
subprogram.......................... 323
Program defaults...................... 449
Programming graphics............. 283
Programming tool movement... 133
Program run............................. 603
Execute................................ 604
Interrupt............................... 605
Mid-program startup............ 613
Overview............................. 603
Resuming after interruption. 609
Retraction............................ 610
Skipping blocks.................... 620
Program-section repeat............ 321
Program Test
Overview............................. 599
Projection in three planes......... 592
Protection zone........................ 630
Pulsing spindle speed.............. 469
Q
Q parameter
Export................................. 395
programming....................... 338
Transfer values to the PLC.. 394
Q-Parameter
Transfer values to the PLC.. 392
Q parameter programming
Additional functions............ 352
Angle functions................... 346
Calculation of circles........... 347
If-then decisions................. 348
Mathematical functions...... 343
Programming notes............ 340
Q parameters........................... 338
Checking............................. 350
Formatted output of............ 357
Local parameters QL.......... 338
Preassigned........................ 413
Programming....................... 400
Residual parameters QR..... 338
String parameters QS.......... 400
R
Radius compensation............... 230
Entering............................... 231
Outside corners, inside
corners................................. 232
Rapid traverse.......................... 204
Reading out machine parameters....
410
Reading system data........ 363, 405
Reference system............ 115, 125
Basic.................................... 118
Input..................................... 122
Machine............................... 116
Tool...................................... 123
Working plane...................... 121
Workpiece............................ 119
Replacing texts......................... 141
Resonance vibration................. 469
Restore..................................... 101
Retraction................................. 610
After a power interruption.... 610
Retraction from the contour..... 441
Returning to the contour.......... 618
Rotary axes.............................. 507
Rotary axis
Reduce display M94............ 509
Shortest-path traverse
M126.................................. 508
Rounded corners...................... 265
Rounding corners M197........... 446
S
Save service files..................... 194
Screen keypad.......................... 174
Screen layout............................. 80
Screen layout of CAD viewer... 296
Search function........................ 140
Selecting a contour from DXF.. 307
Selecting positions from DXF... 310
Selecting the preset................. 127
Selecting the unit of measure.. 132
Select kinematics..................... 631
Set BAUD rate......................... 637
Set data transmission speed.... 637
Software number..................... 636
SPEC FCT................................ 448
Special functions...................... 448
Spindle speed
Entering............................... 222
Status display............................. 84
Additional............................... 86
General.................................. 84
Stop at..................................... 602
Straight line...................... 263, 275
String parameter
Converting............................ 406
Copying a substring............. 404
Finding the length................ 408
Testing................................. 407
String parameters.................... 400
Assign.................................. 401
Chain-linking......................... 402
Reading system data........... 405
Structuring programs................ 179
Subprogram.............................. 319
Any desired NC program..... 323
Superimposing handwheel
positioning M118...................... 439
Surface normal vector.............. 490
Switch-off................................. 516
Switch-on................................. 512