Why does my Hettich ROTOFIX 32 A Laboratory Equipment display a Version Error?
A Version Error on your Hettich Laboratory Equipment means that the wrong machine version is set, causing the control section to skip to the Settings menu. To correct this, use the [t] buttons to set the number 7, press the [STOP] button to save the settings, and then perform a MAINS RESET.
What to do if Hettich ROTOFIX 32 A Laboratory Equipment displays error '-2-'?
If your Hettich Laboratory Equipment shows error '-2-', it means there was a loss of mains power during the centrifugation run, and the run was not completed. You should open the lid and press the [START] button. If necessary, repeat the centrifugation run.
How to fix no display on Hettich Laboratory Equipment?
If your Hettich Laboratory Equipment's display is not working, it could be due to no power or defective mains input fuses. Check the supply voltage and the mains input fuse. Also, ensure the mains switch is set to [I].
What does error '-4-' mean on Hettich Laboratory Equipment and how to fix it?
If your Hettich Laboratory Equipment displays error '-4-', it signals a communication error in either the control or power section. Perform a MAINS RESET to resolve this issue.
What to do if Hettich ROTOFIX 32 A Laboratory Equipment displays error '-5-'?
If your Hettich Laboratory Equipment shows error '-5-', it indicates an overload, possibly due to a defective motor or motor control. Try performing a MAINS RESET to address this issue.
What does error -1- mean on my Hettich Laboratory Equipment?
Error -1- on your Hettich Laboratory Equipment indicates a tacho error, caused by speed pulse failure. Make sure that the device is not switched off while the ‘Rotation’ indicator is lit up and rotating. Wait until the ‘Lid closed’ symbol is displayed (after approximately 100 seconds) and then perform a MAINS RESET.
What does error -F- mean on my Hettich Laboratory Equipment?
Error -F- on your Hettich Laboratory Equipment indicates no rotor detection when starting, meaning no rotor is inserted or the tacho is defective. To attempt to fix this, perform a MAINS RESET.
Why is there no speed indicator on my Hettich Laboratory Equipment?
The absence of a speed indicator on your Hettich Laboratory Equipment may be due to a version error, where the wrong machine version is set, causing the control section to skip to the Settings menu. To fix this, use the [t] buttons to set the number 7, then press the [STOP] button to save the settings, and finally perform a MAINS RESET.
What does error -4- mean on my Hettich ROTOFIX 32 A?
Error -4- on your Hettich Laboratory Equipment indicates a communication issue within the control or power section. To solve this, perform a MAINS RESET.
What does error -6- mean on my Hettich ROTOFIX 32 A?
Error -6- on your Hettich Laboratory Equipment signifies overvoltage, meaning the mains voltage is outside of the acceptable range. Try performing a MAINS RESET and check the mains voltage.
Defines the centrifuge's intended purpose and application.
Details user qualifications and requirements.
Provides critical safety warnings and procedures.
Guide to setting up and connecting the centrifuge.
Procedure for powering the centrifuge on/off.
Guide for safe rotor removal and installation.
Guidelines for loading centrifuge tubes into rotors/buckets.
Procedures for performing centrifugation runs.
How to set and adjust centrifugation parameters.
Detailed instructions for cleaning and disinfecting the device.
Procedures for routine maintenance.
Table of common faults, causes, and remedies.
Steps to perform a main power reset.
Defines the centrifuge's intended purpose and application.
Details user qualifications and requirements.
Provides critical safety warnings and procedures.
Guide to setting up and connecting the centrifuge.
Procedure for powering the centrifuge on/off.
Guide for safe rotor removal and installation.
Guidelines for loading centrifuge tubes into rotors/buckets.
Procedures for performing centrifugation runs.
How to set and adjust centrifugation parameters.
Detailed instructions for cleaning and disinfecting the device.
Procedures for routine maintenance.
Table of common faults, causes, and remedies.
Steps to perform a main power reset.
General| Brand | Hettich |
|---|---|
| Model | ROTOFIX 32 A |
| Category | Laboratory Equipment |
| Language | English |
To Next Page