Honeywell VISTA-128BPT - Page 25

21
SECTION 3: DATA FIELD DESCRIPTIONS
FIELD TITLE and DATA ENTRIES Default Values
∗
31
PABX Access Code
Enter 00-09; B-F (11-15)
[Blank] AAA | EEE AAAAAA | EEE AAAAAA | EEE AAAAAA | EEE
If required, enter the code used to get an outside line before dialing the phone number. These digits will be dialed before
∗33, ∗34, and ∗35, followed by a 2 second pause. 0-9; 11 for *; 12 for #; and 13 for 2 second pause.
NOTE: Each digit it a 2-digit entry, example: if a 9 needs to be dialed before the phone number enter 09 then [∗] to exit.
∗
32
Primary Subscriber’s Account Number (partition-
specific)
Enter 00-09; B-F (11-15)
[Blank] AAA | EEE AAAAAA | EEE AAAAAA | EEE AAAAAA | EEE AAAAAA | EEE AAA
AAA | EE AAAAA | EE AAAA | EE AAAA | EE AAAA | EE
Enter a 4- or 10-digit (depending on report format in ∗45) primary subscriber account number.
• Each number requires a 2-digit entry so as to allow entry of hexadecimal digits (B-F).
• If a 4-digit account number is to be used, enter data only in the first four locations, and enter * in the fifth location.
Example: 4-digit account # 1234 would be 01 02 03 04 ∗.
∗
33
Primary Phone Number
Enter 0-9; #11 for ∗, #12 for #, #13 for a 2-second pause.
AA E E E E E E E E E E E E E
E E E E
Enter the primary central station phone number, up to 17 digits. This is the phone number the control will use to transmit
Alarm and status messages to the central station. Do not fill unused spaces, press ∗ when all digits have been entered.
Enter the secondary phone number to central station, 0-9; #11 for *; #12 for #; and #13 for 2 second pause.
NOTES:
• Attempts to dial 8 times before switching to the secondary number (if used).
• Backup reporting is automatic only if a secondary phone number is entered.
∗
34
Secondary Phone Number
Enter 0-9; #11 for ∗, #12 for #, #13 for a 2-second pause.
A E E E E E E E E E E E E E
E E E E
Provides for a Secondary phone number in
∗
34 and Secondary Acct number in
∗
90 for Dual, Split, and Backup reporting.
• Failure to report after eight attempts, control attempts reporting through the secondary.
∗
90: Sec. Subs. Acct # must be enabled.
• If the control makes it's eight attempts to report using the primary phone number and it cannot
get through, it will then
try 8 times with secondary phone number (all with the secondary account number).
• Enter the secondary phone number to central station, 0-9; #11 for *; #12 for #; and #13 for 2 second pause.
NOTES:
• Anytime the Secondary Phone number is dialed the Secondary Acct # is used.
• If Dual and Split reporting are not enabled in ∗51 and 1∗34, then the Secondary phone number and acct # are used
solely for Backup Reporting.
∗
35
Download Phone Number
Enter 0-9; #11 for ∗, #12 for #, #13 for a 2-second pause.
A E E E E E E E E E E E E E
E E E E
Enter the phone number, up to 17 digits, of the computer modem that will be uploading or downloading the control.
0-9; #11 for *; #12 for #; and #13 for 2 second pause. If entering fewer than 17 digits press * after the last digit has been
entered.
∗
36
Download ID Number
Make entries as 2-digit numbers as follows:
00=0 01=1 02=2 03=3 04=4 05=5
06=6 07=7 08=8 09=9 10=A 11=B
12=C 13=D 14=E 15=F
[Blank] A | E A A | E A A | E A A | E AA | E A A | E A A | E A
A | E
NOTE: THIS FIELD CANNOT BE VIEWED.
Enter eight hexadecimal digits.
NOTE: This field is applicable only if downloading is utilized.