Honeywell VISTA-128BPT - Emergency Evacuation; Fire Escape Plan Recommendations

62
VISTA-128BPT/128BPT-SIA/250BPT PROGRAMMING GUIDE
Z
Z
o
o
n
n
e
e
T
T
y
y
p
p
e
e
S
S
t
t
a
a
r
r
t
t
S
S
t
t
o
o
p
p
27 = Access Point Allows more than one relay to be controlled by activation if access point request.
29 = Momentary Exit This Zone Type is used with VISTA-KEY access control ONLY.
31 = End of Exit Time A relay programed to stop/start on 31 will stop/start on the first Exit time to end
(should be Entry/Exit #1). NOTE: If programmed to pulse on A Zone Type 31
it will pulse at the end of E/E#1 and E/E#2.
32 = Start of Entry
Time
Start of Entry time #1 or #2 activate the
output.
33 = Any Burglary
Alarm
Encompasses alarms on Zone Types:
01 = Entry/Exit #1, Burglary
02 = Entry/Exit #2, Burglary
03 = Perimeter, Burglary
04 = Interior Follower, Burglary
05 = Trouble Day/Alarm Night
07 = 24 Hr. Audible Alarm
10 = Interior Delay, Burglary
34 = Code + [#] + 71
Key Entry
Any user authority level has access to this command.
35 = Code + [#] + 72
Key Entry
Any user authority level has access to this command.
36 = At Bell Timeout
(∗13)
Occurs when the Time Out expires or disarming, which ever happens first.
37 = 2 Times Bell
Timeout
Occurs after two times the Bell Time Out expires or disarming, which ever happens
first.
38 = Chime Follows the chime feature for the
compatible Zone Types, the chime
mode must be enabled.
39 = Fire Alarm System Event '39 Any Fire'
encompasses alarms on zone types:
09 = Fire Without Verification
16 = Fire With Verification
40 = Bypassing Occurs when a zone is bypassed Stops when a bypass is cleared.
41 = AC Power Fail∗
Follows the dialer for AC loss, if AC
loss reporting is randomized (∗19),
the
Output will follow this randomized
time.
Follows AC Restore.
If you set the panel for Normal AC loss reporting, the panel should dial within
about 2 minutes of AC loss and the Output will throw at the same time.
42 = System Battery
Low∗
Follows a panel low battery. Follows the Low Battery Restore.
43 = Communication
failure∗
Follows a telephone communication
failure.
Stop when the “Comm. Failure” has
cleared.
44 = RF Low Battery∗
Follows low battery on a 5800 wireless
transmitter.
Stop when the low battery restores.
45 = Polling Loop
Failure∗
Follows Zone 997 (polling loop short)
regardless if zone 997 has a zone type
programmed.
Follows removal of short on polling
loop.
47 = Console Failure∗
Supervision zones for ECP supervision of zone 8XX, where XX = the device address.
51 = RF Receiver
Failure∗
Supervision zones for ECP supervision of zone 8XX, where XX = the device address.
52 = Kissoff∗
Occurs when a Kissoff from Central Station is received.
54 = Fire Zone Reset∗
STARTS a relay when a FIRE reset
command is entered.
STOP program is usually Zone Type 57.
55 = Disarm + 1
Minute
Starts one minute after disarm.
56 = XX Minutes∗
Not a feature. Requires and entry in programming
location 1∗74 (XX Minutes)
57 = YY Seconds∗
Note a feature. Requires and entry in programming
location 1∗75 (YY seconds).