What to do if hpmont Controller shows 'Too small running current'?
If the hpmont Controller shows a 'Too small running current' message, it may be due to improper settings of F16.14 and F16.15. Correct the setting of F16.14, F16.15, check the connection between the controller and motor, detect controller whether output, and detect whether the output contactor work is normal.
What to do if hpmont Controller shows 'Input voltage phase loss'?
If the hpmont Controller displays 'Input voltage phase loss', the power input to the three-phase unit is experiencing a phase loss fault. Check the three-phase power input.
Why is my hpmont Controller overheating?
The hpmont Controller's heatsink may be overheating due to several reasons: the ambient temperature is too high, there is poor external ventilation, the fan is faulty, or there's a fault in the temperature detection circuit. To resolve this, consider using a controller with a higher power capacity, improve ventilation around the controller, or replace the cooling fan.
How to troubleshoot SCI communication error on hpmont HD3L?
An SCI communication error with the hpmont Controller can arise from a faulty or disconnected communication cable, or errors in communication settings or data. Check the connection, ensure the communication format and baud rate are correctly set, and verify the data is sent according to the MODBUS protocol.
How to fix faulty setting of parameters on hpmont HD3L Controller?
Faulty parameter settings on the hpmont Controller can result from a significant difference in power rating between the motor and controller, or from incorrect motor parameter settings. Select a controller with a suitable power rating and set the correct value of motor parameters.
What causes excessive speed deviation in hpmont Controller?
Excessive speed deviation in the hpmont Controller can stem from a brake or contactor fault, PG pulse number fault, improper settings of F05.19 and F05.20, inadequate controller torque, or incorrect speed-loop PI parameter settings. Try changing the contactor, set the proper PG P/R, correct the setting of F05.19, F05.20, select a controller with bigger capacity or correctly set speed-loop PI parameter.
What to do if hpmont HD3L Controller displays 'Output voltage phase loss'?
If the hpmont Controller indicates 'Output voltage phase loss', there may be a phase disconnection or loss, or the three-phase load is severely unbalanced. Check the connection between the controller and the motor and verify the quality of the motor.
What causes motor over speed in hpmont HD3L Controller?
Motor over speed in the hpmont Controller can be caused by a PG pulse number fault, inadequate controller torque, or incorrect speed-loop PI parameter settings. You can set the proper PG pulse number, select a bigger capacity controller or correctly set speed-loop PI parameter.
How to resolve DC bus undervoltage on hpmont Controller?
DC bus undervoltage on the hpmont Controller can occur at power on/off, if the input voltage is too low, or if there's improper wiring. Check the input power voltage and ensure the wiring is correct.
What to do if hpmont Controller shows 'Acc over voltage'?
If the hpmont Controller is showing an 'Acc over voltage' error, the input voltage might be too high, the deceleration time might be too short, or the wiring is improper. Check the power input, set a proper value for Dec time, and verify the wiring.
General| Brand | hpmont |
|---|---|
| Model | HD3L Series |
| Category | Controller |
| Language | English |
Defines "Danger", "Warning", and "Note" for safety hazard and product operation.
Discusses motor characteristics compared to industrial frequency and thermal protection.
Details about HD3L, including output side, contactors, voltage, and lightning surge protection.
Explains derating of output current based on altitude and provides a derating curve.
Details the model naming convention and its components.
Explains the information provided on the HD3L product nameplate.
Lists rated values for different HD3L models, including capacity, input/output current, and size.
Provides detailed electrical, performance, and protection specifications for the HD3L.
Illustrates and identifies the main components and connection terminals of the HD3L.
Lists essential safety precautions for installing the HD3L controller.
Specifies environmental and physical requirements for the installation location.
Details the recommended mounting direction and clearance for heat dissipation.
Provides dimensional data and weight for different HD3L sizes.
Instructions on how to install and remove the HD3L keypad.
Step-by-step guide for removing the upper and lower plastic covers of the HD3L.
Lists critical safety precautions for electrical wiring and connections.
Guidance on selecting appropriate wiring specifications for accessories.
Covers the main power input and motor output connections.
Illustrates the wiring diagram for connecting power supply and motor.
Highlights safety considerations for control and I/O circuits.
Details the functions and connections of the control board terminals.
Describes the functions and connections of the I/O board terminals.
Information on Modbus communication terminal and RJ45 usage.
Explains jumper settings for signal selection and configuration.
Provides guidance on connecting digital input and output signals.
Details how to correctly install the controller to meet EMC requirements.
Specifies wiring practices to avoid interference and ensure signal integrity.
Addresses considerations for motor cable length and carrier frequency.
Explains proper grounding methods for safety and EMC compliance.
Describes the function and common mistakes in using EMI filters.
Methods to reduce conducted, radiated, and RF interference.
Information on AC input, DC, and AC output reactors.
Introduces operation modes and control modes of the HD3L.
Defines how HD3L receives run and speed commands.
Explains the two control modes: V/f and SVC.
Describes various status indicators and conditions of the controller.
Details different running modes like auto-tuning, inspection, and battery-driven.
Overview of the HD3L keypad layout and key functions.
Explains how the keypad displays status during stop, run, edit, and alarm conditions.
Illustrates common keypad operations like parameter setting and password management.
Provides a checklist and procedure for initial power-up.
Introduces status display parameters for the controller.
Details parameters showing controller series, software versions, and status.
Parameters related to drive status, including speed, frequency, voltage, and current.
Parameters for displaying analogue input and output values.
Parameters showing heatsink temperature, terminal status, and fault information.
Introduces general parameter groups for configuration.
Covers fundamental parameters like motor type, control mode, and operating mode.
Parameters for user password, menu mode, and initialization functions.
Parameters controlling the start and stop sequences, including delays and ramp times.
Parameters for acceleration and deceleration S-curve adjustments for ride comfort.
Defines analogue input characteristic curves for speed and weighing.
Parameters for setting multi-speed, inspection, and battery-driven running speeds.
Parameters for pre-torque selection and digital weighing signal settings.
Parameters for asynchronous motor characteristics and auto-tuning.
Parameters for tuning the speed-loop in vector control mode.
Configuration for digital input and output terminals.
Configuration for analogue input and output terminals, including bias and gain.
Parameters for serial communication settings like data format and baud rate.
Parameters for controlling the LCD keypad display language and contrast.
Parameters related to fan control, brake unit, and speed settings.
Parameters for motor overheat, voltage loss, and fault auto-reset settings.
Parameters related to PWM carrier frequency and overmodulation.
Parameters reserved for factory commissioning before delivery.
Steps for basic commissioning of the elevator system with HD3L.
Recommends analyzing application requirements before designing wiring.
Guides on setting essential parameters for elevator control.
Procedure for performing motor parameter auto-tuning.
Steps for conducting inspection running after auto-tuning.
Adjustments for shake-free start and stop, and leveling precision.
How HD3L receives and processes digital commands for MS control.
How HD3L processes analogue speed and direction commands.
Procedure for enabling battery-driven run mode during power outages.
Lists common faults, their reasons, and corresponding counter-measures.
Provides guidelines for daily and periodic maintenance to ensure longevity.
Details the keypad mounting base and extension cable accessories.
Table listing AC and DC reactor models and their parameters.
Recommendations for selecting braking resistors based on motor power.
Reference to the user manual for the Power Regenerative Unit.
Lists parameters for displaying controller status and running information.
Details parameters related to drive status like speed, frequency, and current.
Parameters for displaying analogue input and output signal values.
Parameters showing heatsink temperature, terminal status, and MODBUS status.
Fundamental parameters for motor type, control mode, and operating mode.
Parameters for user password, menu mode, and function initialization.
Parameters for controlling start/stop delays, ramp times, and zero-speed retention.
Parameters for adjusting acceleration, deceleration, and jerk for ride comfort.
Settings for analogue input characteristic curves.
Parameters for multi-speed, inspection, and battery-driven running speeds.
Parameters for pre-torque selection and digital weighing signal inputs.
Parameters for asynchronous motor characteristics and auto-tuning.
Parameters for tuning the speed-loop in vector control mode.
Configuration settings for digital input and output terminals.
Configuration settings for analogue input and output terminals.
Parameters for serial communication like data format and baud rate.
Parameters for LCD keypad display language and contrast.
Parameters for fan control, brake unit, and speed signal delay.
Parameters for motor overheat, voltage loss, and fault auto-reset settings.
Parameters related to PWM carrier frequency and overmodulation.
To Next Page
