Need help?Do you have a question about the IndigoVision 9000 Range and is the answer not in the manual?
General| Image Sensor | CMOS (various sizes depending on model) |
|---|---|
| Lens Type | Varifocal |
| Video Compression | H.264, MJPEG |
| Audio Compression | G.711 |
| Ethernet | 10/100 Mbps |
| Power | PoE or 12V DC |
| Analytics | Motion detection, tamper detection |
| Day/Night | Yes |
| IR Illumination | Integrated IR LEDs |
| Wide Dynamic Range | Yes |
This guide uses specific formats for warning, caution, and notice safety messages.
Details the different variants of the IndigoVision 9000 SD Fixed Dome available.
Provides details and diagrams for the internal variant of the camera.
Details and diagrams for the standard vandal-resistant dome camera variant.
Details and diagrams for the environmental vandal-resistant dome camera variant.
Describes the camera's connection ports, including RJ45 and analog video connectors.
Details the camera's opto-isolated binary inputs and outputs on the 18-way IO connector.
Outlines the power consumption and requirements for the camera, including PoE.
Specifies the requirements for video BNC and Ethernet cabling.
Details the wiring requirements for the 10-way IO connector.
Lists the items included in the package for the internal variant camera.
Explains the methods for powering up the camera, including PoE and auxiliary power.
Guides users to configure IP settings before final mounting.
Outlines the steps to configure the device using its web-based configuration pages.
Explains how to prepare an isolated network for initial device configuration.
Details how to configure the device using the console port via a serial connection.
Explains how to connect the configured device to the main network.
Provides a four-stage guide for installing the internal variant of the camera.
Details how to drill and prepare the mounting surface for the camera's mounting plate.
Explains how to set up the camera's sensor using analog video output.
Details the procedure for focusing the camera's lens.
Outlines installation options for the standard vandal-resistant variant.
Details the four stages for installing the standard vandal-resistant variant without an exit collar.
Details the five stages for installing the environmental vandal-resistant variant.
Guides on fitting the exit collar to the wall or ceiling for the environmental variant.
Details connecting the 12V power supply for the heater in the environmental variant.
Explains how to connect cables and secure the camera assembly to the exit collar.
Provides guidance on using the 9-22mm lens, including focus compensation for the dome bubble.
Explains performance and warm-up times for the environmental variant in low temperatures.
Instructs on accessing and using the device's web-based configuration interface.
Details how to configure the device's network settings, including DHCP and static IP.
Covers various video parameters like brightness, sharpness, resolution, and exposure.
Describes parameters for video encoding, including resolution, bit rate, and filters.
Explains configuring analytics features like filters and motion detection.
Details available analytics filters like Activity, Motion, and Hooded Camera.
Allows specifying areas of the scene to be monitored or ignored for analytics.
Covers audio input/output gain, source, type, and encoder settings.
Details configuring binary inputs and outputs for event triggering.
Allows specifying authorized network devices and enabling IP address restrictions.
Allows upgrading the device's firmware and license key.
Explains how to disable web configuration for security purposes.
Details video and audio codec specifications, including resolution and color space.
Provides specifications for the camera's CMOS sensor, including active pixels and sensitivity.
Explains the use of the console port for diagnostics and setup, including cable wiring.
Specifies requirements for network connections, including connector type and cable length.
Details operating and storage temperature ranges for different variants.
Lists relevant regulatory standards and approvals, including EMC and safety.
Describes the in-ceiling flush mount for installing the camera in a false ceiling.
Details the bracket wall mount for horizontally mounting the camera on a vertical wall.
Describes the wall mount for installing the camera as a pendant.
Details the swan-neck mount for installing the camera as a pendant.
Describes the vertical mount for installing the camera as a pendant.
Explains NPT adapters for fixing the camera to standard 1.5" NPT mounts.
Details the corner mount adapter for fixing the camera to wall corners.
Describes the pole mount adapter for fixing the camera to a pole.
To Next Page