Copyright © Itech Electronic Co., Ltd.
IX
IT6000B Series User Manual
4.6.1 LIST Function .............................................................................................. 71
4.6.2 Battery Charging/Discharging Test Function .............................................. 78
4.6.3 Built-in Waveform Function ......................................................................... 81
4.6.4 Solar Photovoltaic Curve Simulation Function (SAS) ............................... 139
4.6.5 Battery Simulation Function ...................................................................... 144
5 Load Function................................................................................................................. 149
5.1 Programming the Input ........................................................................................ 149
5.1.1 Select the Operation Mode (Mode) ........................................................... 149
5.1.2 Basic Operation Mode ............................................................................... 150
5.1.3 Complex Operation Mode ......................................................................... 151
5.1.4 Set the Input-On/Input-Off Delay Time （On Delay/ Off Delay） ............. 153
5.1.5 Set I-Rise / I-Fall Slope（I-Rise / I-Fall Slope）........................................ 153
5.1.6 Set V-Rise / V-Fall Slope（V-Rise / V-Fall Slope）.................................. 154
5.1.7 Set P-Rise / P-Fall Slope（P-Rise / P-Fall Slope）.................................. 154
5.1.8 Short-Circuit Analog Function ................................................................... 154
5.1.9 VON Function（Von） .............................................................................. 154
5.2 Advanced Feature................................................................................................ 156
5.2.1 LIST Function ............................................................................................ 156
5.2.2 Battery Discharging Test Function ............................................................ 162
5.3 Protection Function .............................................................................................. 163
5.3.1 Set Over-Current Protection (OCP)........................................................... 165
5.3.2 Set Over-Power Protection (OPP)............................................................. 166
5.3.3 Set Under-Voltage Protection (UVP)......................................................... 166
5.3.4 Over-Temperature Protection (OTP)......................................................... 167
5.3.5 Sense Reverse Protection......................................................................... 168
6 Basic Operation.............................................................................................................. 169
6.1 Local/Remote Mode Switch ................................................................................. 169
6.2 Key Lock Function ............................................................................................... 170
6.3 Save and Recall Operations ................................................................................ 170
6.3.1 Save Operation.......................................................................................... 171
6.3.2 Recall Operation........................................................................................ 172
6.4 Data Logging Function......................................................................................... 172
6.5 Set the Beeper Status (Beep) .............................................................................. 175
6.6 Set the Power-on State (PowerOn) ..................................................................... 176
6.7 Sense Function (Sense) ...................................................................................... 179
6.8 Select Trigger Source (Trig Source) .................................................................... 180
6.9 Set the Communication Information (I/O Con) .................................................... 181
6.10 Set Parallel Operation Mode (Parallel) .............................................................. 181
6.11 Digital I/O Function (Digital Port) ....................................................................... 186
6.11.1 IO–1. Ps-Clear, Not-Invert....................................................................... 190
6.11.2 IO–2. Ps, Not-Invert................................................................................. 192
6.11.3 IO–3. Off-Status, Not-Invert..................................................................... 193
6.11.4 IO–4. Ext-Trig, Not-Invert ........................................................................ 195
6.11.5 IO–5. INH-Living, Not-Invert .................................................................... 198
6.11.6 IO–6. Sync-On, Not-Invert....................................................................... 201
6.11.7 IO–7. Sync-Off, Not-Invert....................................................................... 203
6.12 Source Analogue Function (Ext-Program) (Optional) ....................................... 205
6.13 loadAnalogue Function (Ext-Program) (Optional) ............................................. 210
6.14 Restored to Factory Setting (System Reset) ..................................................... 215
6.15 View the System Information (System Info) ...................................................... 220
6.16 Observe Power Grid Information (AC-Meter) .................................................... 221
6.17 Display Loading Time (Disp on timer)................................................................ 222
6.18 System Upgrade ................................................................................................ 222
7 Technical Specification .................................................................................................. 226
7.1 Main Specification................................................................................................ 226
7.1.1 IT6005B-80-150......................................................................................... 227
7.1.2 IT6010B-80-300......................................................................................... 231
7.1.3 IT6015B-80-450......................................................................................... 235
To Next Page
Need help?
General
