ITech IT6000B Series - 7 Technical Specification; 7.1 Main Specification

309 pages

To Next Page

To Previous Page

Technical Specification

7 Technical Specification

This chapter will introduce the main technical parameters of thispower, such as

rated voltage/current/power and so on. Besides, we will introduce the working

environment and storage temperature.

♦ Main Specification

♦ Supplemental Characteristics

7.1 Main Specification

226

Main Page

Warranty3
Limitation of Warranty3
Safety Symbols4
Safety Precautions4
Environmental Conditions6
Regulation Tag7
Waste Electrical and Electronic Equipment (WEEE) Directive8
Compliance Information9
Table of Contents10
Quick Reference13
Brief Introduction13
Front-Panel Overview15
Keyboard Introduction16
Push-On Knob19
Rear Panel Introduction20
VFD Indicator Lamps Description21
Configuration Menu Function22
System Menu Function25
Options Introduction30
Inspection and Installation33
Unpacking and Transportation33
Verifying the Shipment36
Instrument Size Introduction37
Connecting the Power Cord38
Connecting the Device under Test (DUT)44
Remote Interface Connection48
USB Interface48
LAN Interface49
CAN Interface54
GPIB Interface (Optional)56
Interface (Optional)57
Getting Started59
Power-On Self-Test59
Source Mode/ Load Mode Switch63
Set Output/Input Value64
Use the Front Panel Menu65
On/Off Control66
Power Supply Function67
Set the Output Voltage67
Set the Output Current67
Set the Output Power68
Config Menu for Power Supply68
Set the CC/CV Priority Mode68
Set the Internal Resistance73
CR Function in Sink Mode73
Set the Output-On/Output-Off Delay74
Protection Function for Power Supply74
Set Over-Voltage Protection (OVP)77
Set Over-Current Protection (OCP)78
Set Over-Power Protection (OPP)79
Set Under-Current Protection (UCP)80
Set Under-Voltage Protection (UVP)81
Over-Temperature Protection (OTP)82
Sense Reverse Protection82
Function Menu for Power Supply83
LIST Function83
Battery Charging/Discharging Test Function90
Built-In Waveform Function93
Solar Photovoltaic Curve Simulation Function (SAS)151
Battery Simulation Function156
Load Function161
Programming the Input161
Select the Operation Mode (Mode)161
Basic Operation Mode162
Complex Operation Mode163
Set the Input-On/Input-Off Delay Time （On Delay/ off Delay165
Set I-Rise / I-Fall Slope（I-Rise / I-Fall Slope165
Set V-Rise / V-Fall Slope（V-Rise / V-Fall Slope166
Set P-Rise / P-Fall Slope（P-Rise / P-Fall Slope166
Short-Circuit Analog Function166
VON Function（Von166
Advanced Feature168
LIST Function168
Battery Discharging Test Function174
Protection Function175
Set Over-Current Protection (OCP)177
Set Over-Power Protection (OPP)178
Set Under-Voltage Protection (UVP)178
Over-Temperature Protection (OTP)179
Sense Reverse Protection180
Basic Operation181
Local/Remote Mode Switch181
Key Lock Function182
Save and Recall Operations182
Save Operation183
Recall Operation184
Data Logging Function184
Set the Beeper Status (Beep)187
Set the Power-On State (Poweron)188
Sense Function (Sense)191
Select Trigger Source (Trig Source)192
Set the Communication Information (I/O Con)193
Set Parallel Operation Mode (Parallel)193
Digital I/O Function (Digital Port)198
IO-1. Ps-Clear, Not-Invert202
IO-2. Ps, Not-Invert204
IO-3. Off-Status, Not-Invert205
IO-4. Ext-Trig, Not-Invert207
IO-5. INH-Living, Not-Invert210
IO-6. Sync-On, Not-Invert213
IO-7. Sync-Off, Not-Invert215
Source Analogue Function (Ext-Program) (Optional)217
Loadanalogue Function (Ext-Program) (Optional)222
Restored to Factory Setting (System Reset)227
View the System Information (System Info)232
Observe Power Grid Information (AC-Meter)233
Display Loading Time (Disp on Timer)234
System Upgrade234
Technical Specification238
Main Specification238
It6005B-80-150239
It6010B-80-300243
It6015B-80-450247
It6006B-300-75252
It6012B-300-150256
It6018B-300-225260
It6006B-500-40265
It6012B-500-80269
It6018B-500-120273
It6006B-800-25278
It6012B-800-50282
It6018B-800-75286
It6018B-1500-40290
It6018B-2250-25295
Supplemental Characteristics300
Routine Maintenance301
Instrument Self-Test301
Cleaning and Maintenance301
Contact of ITECH Engineers302
Return for Repair303
A Appendix305
Specifications of Red and Black Test Cables305
Fuse Replacement306

ITech IT6000B Series - 7 Technical Specification; 7.1 Main Specification

Table of Contents

Related product manuals