Jandy APUREM - Figure 20 B. Purelink Power Center, 6614 AP; Figure 20 C. Purelink Power Center, 6613 AP

52 pages

Save Page as PDF

To Next Page

To Previous Page

Figure 20c. PureLink Power Center, 6613AP

2, 3

4, 6

Figure 20b. PureLink Power Center, 6614AP

2, 3

4, 6

Page 47

ENGLISH

Page 47

ENGLISH

Jandy

AquaPure

/PureLink™ Power Center and Cell Kit

Installation and Operation Manual

Main Page

Table of Contents2
Section 1. Important Safety Instructions4
Section 2. System Description7
Product Description7
Figure 1. Typical Aquapure and Purelink Installation Example with Options7
Electrical Specifications8
Figure 2A. Wiring Diagram for the Purelink9
Figure 2C. Wiring Diagram for the Aquapure11
Section 3. Installation Instructions12
Materials and Tools12
Plumbing Configurations12
Recommended Electrolytic Cell and Sensor Orientation12
Recommended Plumbing Configuration13
TM System13
Figure 3. Chlorine Generator Cell and Sensor Orientation with Flow Direction13
Figure 4. Recommended Plumbing Configuration for Pool/Spa Combination Systems13
Installing Aquapure and Purelink Control/Power Centers14
Figure 5. Recommended Plumbing Configuration for Pool or Dual Equipment Systems14
Figure 6. Removing the Control/Power Center Mounting Brackets from Shipping Position14
Earth Bonding (Grounding)15
Figure 8. Reinstall Mounting Brackets on15
Model Configuration16
Installation of the Chlorine Generator User16
Figure 9. Chlorine Generator Power Interface Board16
Figure 10. Installation of the User Interface16
Installing the Electrolytic Cell and Flow/Temp/Salinity Sensor17
New Installation17
Replacement of Existing 3-Port Cell (Universal or 2" PVC Unions)18
Replacement of Old 2-Port (Square) Cell with New 3-Port Cell19
Option Selection Tool19
Figure 11. Cell Installation and Flow/Temp/Salinity Sensor21
Figure 12. Pipe Cutout22
Figure 13. Pipe Cutout (Option 3 - Replace 2-Port Cell and Piping and Treat as New Installation)22
Connection of Chlorine Generator Electronics to an Aqualink Control System23
Wiring Aquapure Control Center to an Aqualink Power Center23
Figure 14. Power Connection between Aquapure Control Center and Aqualink Power Center23
Figure 15. Communication Connection between Aquapure Control Center and Aqualink Control System23
Operation of External Control/Orp Control Board25
Figure 17. Movable ORP Jumper J1425
Section 4. Pool Water Preparation26
Determining Pool Size (Liters of Water in Your Pool)26
Determining Pool Size (Gallons of Water in Your Pool)26
Selecting Model Size26
Optimum Pool Water Conditions28
Chlorine Testing28
Salt (Nacl Sodium Chloride)29
When to Add Salt29
What Type of Salt to Use29
How Much Salt to Use29
How to Add Salt to the Pool29
Approximate Kilograms (Pounds) of Salt Needed to Obtain 3.0 Gpl (3,000 PPM) in Pool30
Section 5. Operating Instructions31
User Interface Controls31
Reading the Display32
Control/Power Center32
Operation34
Startup35
Shocking35
Apply Power35
Operating in Winter35
Recommendations36
Section 6. User Maintenance Instructions37
Daily37
Monthly37
Electrolytic Cell Cleaning - as Needed37
Flow/Temp/Salinity Sensor Cleaning38
Winterizing39
Figure 19. Spool Piece Location39
Section 7. Troubleshooting40
Problems and Corrective Action40
Level 2 Service Codes43
Section 8. Temperature Conversion45
Section 9. Aquapure and Purelink Exploded Views and Replacement Kits46
Aquapure and Purelink Control/Power Center Replacement Parts46
Figure 20A. Aquapure Control Center46
Figure 20B. Purelink Power Center, 6614AP47
Figure 20C. Purelink Power Center, 6613AP47
3-Port Electrolytic Cell and Sensor Replacement Parts with Universal Unions (2"-2½")48
Figure 21. 3-Port Electrolytic Cell and Sensor48
Figure 22. 3-Port Spool Exploded View48
3-Port Electrolytic Cell and Sensor Replacement Parts (2" PVC Unions)49
Figure 23. 3-Port Electrolytic Cell and Sensor Exploded View (2" PVC Unions)49
Figure 24. 3-Port Spool Exploded View49

Jandy APUREM - Figure 20 B. Purelink Power Center, 6614 AP; Figure 20 C. Purelink Power Center, 6613 AP

Table of Contents

Related product manuals