JUKI SC-922 Engineer's Manual

– 21 –
1 Soft start The number of stitches to be sewn at a low speed when 0 to 9 U 31
function the soft-start function is used at the start of sewing. (Stitches)
0 : The function is not selected.
1 to 9 :The number of stitches to be sewn under
the soft start mode.
2 Material end Material end sensor function (to be used only with 0/1 U 31
sensor CP-18).
function 0 : Material end detection function is not operative
1 : After detecting material end, the specified
number of stitches (No. 4) will be sewn, and
the sewing machine will stop.
3 Thread trimming Thread trimming function by material end sensor 0/1 U 31
function by (to be used only with CP-18).
material end 0 : Automatic thread trimming function after detection
sensor of material end is not operative.
1 : After detecting the material end. sewing will be
carried out for the specified number of stitches
(No. 4) and the sewing machine will then stop.
4 Number of Number of switches for material end sensor (to be 0 to 19 U 31
stitches for used only with CP-18). (Stitches)
material end Number of stitches from detection of material end to
sensor stop of the sewing machine
5 Flicker reducing Flicker reducing function 0/1 U 31
function 0 : Flicker reducing function is not operative.
1 : Flicker reducing function is effective.
6 Bobbin thread Bobbin thread counting function 0/1 U 31
counting 0 : Bobbin thread counting function is not operative. 35
function 1 : Bobbin thread counting function is operative.
7 Unit of bobbin Unit of bobbin the thread counting down 0 to 3 U
thread counting 0 : 1 Count/10 stitches
down 1 : 1 Count/15 stitches
2 : 1 Count/20 stitches
3 : 1 Count/thread trimming
8 Number of Sewing speed of reverse feed stitching 150 to 3000 U
rotation of (sti/min)
reverse feed
stitching
9 Thread trimming Thread trimming prohibiting function ( to be used 0/1 U 31
prohibiting only with CP-18).
function 0 : Thread trimming prohibiting function is not
operative.
1 : Thread trimming is prohibited. (Output of solenoid
is prohibited. : Thread trimmer and wiper)
10 Setting of needle Position of needle bar is specified when the sewing 0/1 U 31
bar stop position machine stops.
when the sewing 0 : Predetermined lowest position
machine stops 1 : Predetermined highest position
11 Operation Operation confirmation sound for operation panel 0/1 U 31
confirmation 0 : Operation confirmation sound is not generated
sound for 1 : Operation confirmation sound is generated
operation panel
12 Optional switch Switching of function of optional switch. U 32
function selection
13 Function of Function of prohibiting start of the sewing machine 0 to 2 U
prohibiting start by bobbin thread counting
of the sewing 0 : When counting is out (-1 or less) Function of
machine by prohibiting start of the sewing machine is not
bobbin thread operative.
counter 1 : When counting is out (-1 or less) Function of
prohibiting start of the sewing machine is operative.
2 : When counting is out (-1 or less) Function of
forcibly prohibiting start of the sewing machine
is operative.
No. Item Description Setting range Setting level
∗ Do not change the set values with asterisk (∗) mark as they are functions for maintenance. If the standard set value set at the time
of delivery is changed, it is in danger of causing the machine to be broken or the performance to be deteriorated.
(8) Function setting list (Start level ; U : User’s mode, S : Service mode)
∗
∗
1
1
2
0
3
0
4
5
5
0
6
1
7
0
8
0
0
6
9
0
0
1
0
1
1
1
2
1
T
P
o
3
1
0
∗
Indication of
function setting
Ref.
page

JUKI SC-922 Specifications

General

Brand	JUKI
Model	SC-922
Category	Sewing Machine
Language	English