– 65 –
(2) One-touch settable item list
No. Function item
0 No function noP
1 Soft start stitching count SoFT
2 Material end sensor function Ed
3 Thread trimming function by material end sensor EdTr
4 Number of stitches for material end sensor EdST
6 Bobbin thread count function bob
7 Unit of bobbin thread counting down rSTi
8 Rotation count of reverse feed stitching SbT
9 Thread trimming prohibiting function TrM
10 Needle bar position specifying at machine stop nPS
11 Operating sound of operation panel SUnd
13 Function of prohibiting start of sewing ASCT
machine by bobbin thread counter
14 Sewing counter nTo
15 Function of thread wiping after thread trimming WiP
21 Neutral presser lifting function nPL
22 Function of switching needle up/down CMSP
compensating switch function
25
Thread trimming after rotating handwheel by hand
CUTC
29 Back tack initial motion time TrSS
30 Function of reverse feed stitching on the way obT
31 Reverse feed stitching count on the way nobT
32 Effective condition of reverse feed stitching obTS
on the way at machine stop
33 Thread trimming function by reverse feed obTT
stitching on the way
35 Number of rotation at low speed SPoS
36 Number of thread trimming rotation STrM
37 Number of soft start rotation SSFT
38 One-shot speed SASS
47 Holding time of automatic presser lifting TFL
49 Work clamp lowering time TFLW
50 Setting of pedal specifications FTr2
51 Solenoid timing on compensation of reverse TSon
feed stitching at sewing start
52 Solenoid timing off compensation of reverse TSoF
feed stitching at sewing start
53 Solenoid timing off compensation of reverse TEoF
feed stitching at sewing end
55
Function of work clamp lifting after thread trimming
FLAT
56 Function of lifting needle in a reverse rotation rATr
after thread trimming
58 Function of holding needle bar at predetermined HPoS
up/down positions
59 Function of A/M switching of reverse feed SbTo
stitching at sewing start
60 Function of stop immediately after reverse SbTq
feed stitching at sewing start
61 Time of holding needle bar at predetermined THPS
position
64 Switching speed of condensation and EBT SEST
70 Work clamp soft down function SdFL
No. Function item
71 Double reverse feed stitching function ACrA
72 Machine startup selection function FACr
73 Retry function FrET
74 Function setting of MF thread trimming device MFTr
76 One-shot function SHoT
84 Initial suction time of presser solenoid TPUT
87 Pedal curve selection function FPoS
91 Function of prohibiting compensating PMAT
operation after rotating handwheel by hand
92 Function of reducing reverse feed stitching dSbT
speed at sewing start
93 Function of adding the needle up/down MAdF
compensating switch
94 Function of nonstop sewing between SbTC
continuous stitching and one-shot stitching
96 Setting of maximum rotation speed SPd
103 Delay time of needle cooler output OFF TndL
124 Setting of energy saving function at standby SAvE
144 Setting of stitches count for canceling dLST
alternate vertical output
146 Selection of alternate vertical output after TrdL
thread trimming
147 Alternate vertical initial output dL
148 2-pitch output during reverse feed stitching SE2P
at start and end
149 2-pitch inverted output during alternate dL2P
vertical output
150 2-pitch initial output 2PiT
151 Tie stitch adjustment function bTP
154 Function of shortened stitching at start and SESS
end
155 Setting of neutral automatic presser lifting nPLd
156 Thread clamp function TC
158 Function of shortened stitching during TrSS
thread trimming
163 Alternate vertical speed limit function FdLS
164 High-speed switching function by standing PdHi
pedal input
168 Remaining bobbin thread detection function bTd
Abbrevi-
ation
Abbrevi-
ation
To Next Page
Loading...
Need help?
General
