Keysight U1732C - List of Figures

Keysight U1731C/U1732C/U1733C User’s Guide 13
List of Figures
Figure 1-1 Installing the batteries . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 1-2 Power-on button . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Figure 1-3 Tilt-stand adjustment and IR cable connection . . . . .24
Figure 1-4 Keysight GUI Data Logger Software . . . . . . . . . . . . . .25
Figure 1-5 Width dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Figure 1-6 Height and depth dimensions . . . . . . . . . . . . . . . . . . .28
Figure 1-7 Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Figure 1-8 Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Figure 2-1 Using the Ai function . . . . . . . . . . . . . . . . . . . . . . . . . .42
Figure 2-2 Inductance measurement with Q factor . . . . . . . . . . .45
Figure 2-3 Measuring inductance . . . . . . . . . . . . . . . . . . . . . . . . .46
Figure 2-4 Capacitance measurement with D factor . . . . . . . . . .47
Figure 2-5 Measuring capacitance . . . . . . . . . . . . . . . . . . . . . . . .48
Figure 2-6 Resistance measurement . . . . . . . . . . . . . . . . . . . . . . .49
Figure 2-7 Measuring resistance . . . . . . . . . . . . . . . . . . . . . . . . . .50
Figure 2-8 Impedance measurement with theta . . . . . . . . . . . . . .51
Figure 2-9 Measuring impedance . . . . . . . . . . . . . . . . . . . . . . . . .52
Figure 2-10 Component above setting tolerance . . . . . . . . . . . . . .54
Figure 2-11 ESR measurement with theta . . . . . . . . . . . . . . . . . . .55
Figure 2-12 DCR measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Figure 2-13 Using the Hold function . . . . . . . . . . . . . . . . . . . . . . . .56
Figure 2-14 Using the Rec function . . . . . . . . . . . . . . . . . . . . . . . . .57
Figure 2-15 Using the Limit function . . . . . . . . . . . . . . . . . . . . . . . .59
Figure 2-16 High and low limit values . . . . . . . . . . . . . . . . . . . . . . .60
Figure 2-17 nGo and Go indications . . . . . . . . . . . . . . . . . . . . . . . .60
Figure 2-18 Using the Null function . . . . . . . . . . . . . . . . . . . . . . . .61
Figure 2-19 Using the Cal function . . . . . . . . . . . . . . . . . . . . . . . . .63
Figure 2-20 Open calibration and short calibration prompts . . . . .63
Figure 3-1 Changing the power-on measurement type . . . . . . . .71
Figure 3-2 Changing the power-on test frequency . . . . . . . . . . . .72
Figure 3-3
Changing the power-on secondary parameter and measurement
mode for inductance (L) measurements
. . . . . . . . . . . .73
Figure 3-4
Changing the power-on secondary parameter and measurement
mode for capacitance (C) measurements
. . . . . . . . . . .74