Maintenance - Gearbox
86
Pos: 131.1 /Übersc hriften/Überschri ften 2/U-Z/Winkelgetr iebe @ 0\mod_1197005918 299_78.docx @ 15435 @ 3 @ 1
13.3 Angular gearbox
Pos: 131.2 /Abkürzun gen /CR-Ausführung @ 194\ mod_1383299073254_78. docx @ 1647987 @ @ 1
CR design
Pos: 131.3 /Übersc hriften/Überschri ften 3/K-O/Oberteil @ 10\ mod_1221639445993_78. docx @ 135690 @ 3 @ 1
13.3.1 Top part
Pos: 131.4 /BA/W artung/Hinweis Ölstands kontrolle in Arbeitsste llung und in waagerech ter Stellung der Maschi ne vornehmen @ 194\mod_13835 54973754_78.doc x @ 1649577 @ @ 1
Note
Perform oil level check and oil change while the machine is in a horizontal position!
Pos: 131.5 /BA/W artung/Ölkontrolle_Wec hsel/Mähwerke/Bi ld Winkelgetriebe Obert eil CRI @ 10\mod_1221555 831463_78.docx @ 135326 @ @ 1
EC-210-0
2
1
Figure 44
Pos: 131.6 /BA/W artung/Ölkontrolle_Wec hsel/Ölwechsel / Ölkon trolle:Legende zu Grafik Kontrollschr aube / Einfüllschraube @ 194\ mod_1383298407773 _78.docx @ 1647929 @ @ 1
1) Inspection screw / control hole 2) Filler plug / oil filling hole
Pos: 131.7 /BA/W artung/Ölkontrolle_Wec hsel/Ölqualität / Ölmenge: siehe Kapitel Tec hnische Daten @ 134\mod_13 50483480921_78.doc x @ 1188085 @ @ 1
Oil Quality / Amount of Oil: Refer to Chapter Technical Data “Lubricants”
Pos: 131.8 /BA/W artung/Ölkontrolle_Wec hsel/Ölkontroll e / Ölwechsel Intervall: si ehe Kapitel Wartung „ Wartungstabelle“ @ 134\ mod_1350483605921_78. docx @ 1188115 @ @ 1
Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”
Pos: 131.9 /BA/W artung/Ölkontrolle_Wec hselÖlkontrolle NEU über Kontrollschraube @ 140\ mod_1355141753680_ 78.docx @ 1244582 @ @ 1
Oil level check:
• Screw out inspection screw.
• Oil level up to control hole.
If the oil reaches the control hole:
• Screw in the inspection screw and tighten it securely.
If the oil does not reach the control hole:
• Screw out filler plug.
• Top up oil via oil filling hole until the control hole is reached.
• Screw in the inspection screw and the filler plug and tighten them securely.
Pos: 131.10 /BA/W artung/Ölkontrolle_W echsel/Ölwechsel NEU Kontrollschraube, Einfüllschraube Öl absaug en @ 207\mod_13867735996 51_78.docx @ 1716145 @ @ 1
Oil change:
Collect escaping oil in a suitable container.
• Screw out inspection screw and filler plug and drain the oil.
• Top up new oil via oil filling hole until the control hole is reached.
• Screw in inspection screw and filler plug and tighten them securely.
Pos: 131.11 /BA/W artung/Ölkontrolle_W echsel/Hinweis - A ltöl ordnungsgemäß entsorgen @ 0\ mod_1197008117002_7 8.docx @ 15550 @ @ 1
Note
The used oil must be disposed of correctly
Pos: 132 /Layout Module /---------------Seitenumbruch--------------- - @ 0\mod_1196175311226_0. docx @ 4165 @ @ 1
To Next Page
Loading...