Maintenance - Gearbox
87
Pos: 133.1 /Übersc hriften/Überschri ften 2/U-Z/Winkelgetr iebe @ 0\mod_1197005918 299_78.docx @ 15435 @ 3 @ 1
13.4 Angular gearbox
Pos: 133.2 /Abkürzun gen /CR-Ausführung @ 194\ mod_1383299073254_78. docx @ 1647987 @ @ 1
CR design
Pos: 133.3 /Übersc hriften/Überschri ften 3/U-Z/Untertei l @ 10\mod_1221640227712 _78.docx @ 135712 @ 3 @ 1
13.4.1 Bottom part
Pos: 133.4 /BA/W artung/Hinweis Ölstands kontrolle in Arbeitsste llung und in waagerech ter Stellung der Maschi ne vornehmen @ 194\mod_13835 54973754_78.doc x @ 1649577 @ @ 1
Note
Perform oil level check and oil change while the machine is in a horizontal position!
Pos: 133.5 /BA/W artung/Ölkontrolle_Wec hsel/Mähwerke/Bi ld Winkelgetriebe CRI @ 0\mod_1197013688111_78.d ocx @ 15844 @ @ 1
EC-189-0
1
2
Fig. 45:
Pos: 133.6 /BA/W artung/Ölkontrolle_W echsel/Ölwechsel / Ölkon trolle:Legende zu Grafik Kontrollschr aube / Ablassschraube @ 194\m od_1383299451132_78. docx @ 1648045 @ @ 1
1) Inspection screw / control hole 2) Drain plug
Pos: 133.7 /BA/W artung/Ölkontrolle_Wec hsel/Ölqualität / Ölmenge: siehe Kapitel Tec hnische Daten @ 134\mod_13 50483480921_78.doc x @ 1188085 @ @ 1
Oil Quality / Amount of Oil: Refer to Chapter Technical Data “Lubricants”
Pos: 133.8 /BA/W artung/Ölkontrolle_Wec hsel/Ölkontroll e / Ölwechsel Intervall: si ehe Kapitel Wartung „ Wartungstabelle“ @ 134\ mod_1350483605921_78. docx @ 1188115 @ @ 1
Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”
Pos: 133.9 /BA/W artung/Ölkontrolle_Wec hselÖlkontrolle NEU über Kontrollschraube o hne Einfüllschraube @ 158\mod_136448363358 9_78.docx @ 1391741 @ @ 1
Oil level check:
• Screw out inspection screw.
• Oil level up to control hole.
If the oil reaches the control hole:
• Screw in the inspection screw and tighten it securely.
If the oil does not reach the control hole:
• Top up oil via control hole until the control hole is reached.
• Screw in the inspection screw and tighten it securely.
Pos: 133.10 /BA/W artung/Ölkontrolle_W echselÖlwechsel NEU ohne Ei nfüllschraube @ 158\ mod_1364483760090_78. docx @ 1391770 @ @ 1
Oil change:
Collect escaping oil in a suitable container.
• Screw out oil drain plug and drain the oil.
• Screw out inspection screw.
• Screw in oil drain plug and tighten it securely.
• Top up new oil via control hole until the control hole is reached.
• Screw in the inspection screw and tighten it securely.
Pos: 133.11 /BA/W artung/Ölkontrolle_W echsel/Hinweis - A ltöl ordnungsgemäß entsorgen @ 0\ mod_1197008117002_7 8.docx @ 15550 @ @ 1
Note
The used oil must be disposed of correctly
Pos: 134 /Layout Module /---------------Seitenumbruch--------------- - @ 0\mod_1196175311226_0. docx @ 4165 @ @ 1
To Next Page
Loading...