EasyManua.ls Logo

KUHN FC3160 TCD - User Manual

KUHN FC3160 TCD
128 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Original instructions
KN284EGB_A
Read carefully before starting the machine
Operator's manual
Mower conditioner
---A1011-00E00001 > ---A1011-00E99999
FC3160-3560-4060 TCD
KN284EGB_A
- English - 01-2019
*KN284EGB_A*

Table of Contents

Questions and Answers

  • B
    benjamin00Aug 8, 2025
    How to fix uneven stubble with KUHN Farm Equipment?
    • R
      Robert MillerAug 8, 2025
      To address uneven stubble with your KUHN Farm Equipment, start by checking the knives. Dull or broken knives should be replaced immediately. Ensure that the knives are installed correctly, with the arrow on the knife's upper face pointing in the disc's direction of rotation. Also, consider reducing ground speed, adjusting the cutting height, and adjusting the mowing unit ground pressure. If you are dealing with tangled and down crops, try reducing the cutting height or increasing the mowing unit ground pressure.
  • J
    Jennifer WelchAug 12, 2025
    What to do if soil builds up in front of the cutterbar on KUHN Farm Equipment?
    • E
      Eric SimsAug 13, 2025
      If you notice soil building up in front of the cutterbar of your KUHN Farm Equipment, it might be due to too much cutterbar down pressure or very wet working conditions. To resolve this, adjust the mowing unit ground pressure and adjust the cutting height.
  • J
    Jessica MccarthyAug 17, 2025
    What to do if the conditioning rotor of KUHN Farm Equipment is obstructed?
    • L
      Laura SteinAug 17, 2025
      If the conditioning rotor of your KUHN Farm Equipment is obstructed, it could be due to several reasons. First, ensure that the finger conditioning rotor speed is sufficient. Next, check that the PTO speed is correct, referring to the decal on the machine. Lastly, make sure the swath shields are not too closed; open them if necessary.
  • M
    Michael DelacruzAug 21, 2025
    Why are windrows badly shaped with KUHN Farm Equipment?
    • S
      Scott OrtizAug 21, 2025
      If your KUHN Farm Equipment is producing badly shaped windrows, there are a few potential causes. Check the PTO speed, referring to the decal fitted on the machine. If the rotor speed is too high, select the tortoise position to obtain a rotor speed of 780 min-1. Also, ensure that both swath shields are correctly adjusted.
  • A
    April JohnstonAug 25, 2025
    Why does KUHN Farm Equipment require too much pull power?
    • P
      Patricia JordanAug 26, 2025
      If your KUHN Farm Equipment requires too much pull power, it could be due to excessive cutterbar down pressure. Adjust the mowing unit ground pressure to alleviate this issue.
  • B
    blakeclaytonAug 29, 2025
    How to stop rotor finger rattle in KUHN Farm Equipment?
    • H
      hollysimonAug 30, 2025
      If you hear a rotor finger rattle in your KUHN Farm Equipment, it could be due to insufficient rotor speed, a conditioning hood that is too closed, or excessive ground speed. Select the hare position to obtain a rotor speed of 1000 min-1. Position the rotor conditioning hood further away. Reduce ground speed.
  • A
    Amy JacobsSep 3, 2025
    What causes wide spreading of poor quality with KUHN Farm Equipment?
    • V
      Victoria GarciaSep 3, 2025
      If you are experiencing wide spreading of poor quality with your KUHN Farm Equipment, the issue might be with the cover position. Tip the cover over the wide spreading device.

KUHN FC3160 TCD Specifications

General IconGeneral
BrandKUHN
ModelFC3160 TCD
CategoryFarm Equipment
LanguageEnglish

Related product manuals