Why are images skewed when printing from my Kyocera TASKalfa 250ci?
Skewed images from your Kyocera All in One Printer may be caused by: * Incorrectly placed originals on the platen. Align them with the original size indicator plates. * Incorrectly placed originals in the optional document processor. Align the original width guides securely before placing the originals. * Incorrectly loaded paper. Check the position of the paper width guides.
Why does my Kyocera TASKalfa 250ci All in One Printer often jam?
Frequent paper jams in your Kyocera All in One Printer could be due to: * Incorrectly loaded paper. Load the paper correctly. * Unsupported or poor condition paper. Remove the paper, turn it over, and reload it. * Curled, folded, or wrinkled paper. Replace the paper with new paper. * Loose scraps or jammed paper in the machine. Remove any jammed paper.
Why Kyocera TASKalfa 250ci All in One Printer cannot receive document?
There are several reasons the device might not be able to receive documents: * Make sure the modular cord is correctly connected. * If a communication error is displayed, resolve the error and ask the sender to retry. * If RX (reception) restriction is activated, cancel the RX restriction.
Why Kyocera TASKalfa 250ci All in One Printer cannot perform memory forwarding using a sub address?
The reasons why memory forwarding using a sub address may fail: * The recipient fax machine must have a sub address transmission feature for this function to work. * The entered sub address must match the one registered in the recipient fax machine. If your entry is correct, check with the recipient. Note: This machine does not use a sub address password for reception.
What to do if Kyocera All in One Printer displays 'FAX box limit exceeded'?
If the FAX Box limit is exceeded on your Kyocera All in One Printer, it means the FAX Box capacity is full with document data. Press [End] to cancel the job. To proceed, either print or delete the data in the FAX Box, and then try the job again.
Why are the printouts from my Kyocera TASKalfa 250ci All in One Printer dirty?
Dirty printouts from your Kyocera All in One Printer may be due to: * A dirty platen or document processor. Clean them. * A dirty transfer roller. Brush the transfer roller clean. * A dirty drum. Carry out Drum Refresh. * Carry out Developer Refresh. * A dirty scanner. Carry out Laser Scanner Cleaning. * The Printed Document Guard Kit being enabled. Disable the Printed Document Guard Kit.
How to fix light printouts on my Kyocera TASKalfa 250ci All in One Printer?
If your Kyocera All in One Printer's printouts are too light, consider the following: * If the machine is in Auto Density mode, set the correct density level for auto density. * If the machine is in Manual Density mode, use [Image Quality] to set the correct density level. * Shake the toner container from side to side several times to evenly distribute the toner. * If there is a message indicating the addition of toner, replace the toner container. * If the paper is damp, replace it with new paper. * Carry out Drum Refresh. * Carry out Developer Refresh. * Carry out Laser Scanner Cleaning. * If EcoPrint mode is enabled, disable it.
Why my Kyocera TASKalfa 250ci All in One Printer cannot print?
There could be several reasons why your Kyocera All in One Printer cannot print: * The power cord might not be plugged into an AC outlet. Plug it in. * The main power switch might not be turned on. Turn it on. * The printer cable might not be connected securely. Connect the correct printer cable securely. * The machine might have been powered on before the printer cable was connected. Power on the machine after connecting the printer cable. * 'Press Status Key...' might be displayed at the top of the screen. Press the Status/Job Cancel key, [Printing Jobs], and then [Resume All Print Jobs] to restart printing.
What to do if my Kyocera All in One Printer has a paper jam?
If a paper jam occurs, the Kyocera All in One Printer will stop, and the location of the jam will be indicated on the touch panel. Leave the machine on and follow the instructions to remove the jammed paper.
Why Kyocera All in One Printer cannot send document?
If your Kyocera All in One Printer cannot send a document, make sure the modular cord is correctly connected. If a send error is displayed, identify the cause of the error and try sending again. Also, verify whether TX (transmission) restriction is activated and, if so, cancel the TX restriction.
General| Functions | Print, Copy, Scan, Fax |
|---|---|
| Copy Resolution | 600 x 600 dpi |
| Duplex Printing | Standard |
| Type | Color Multifunctional |
| Print Speed | 25 ppm |
| Print Resolution | 600 x 600 dpi, Multi-bit technology for print quality of 9, 600 x 600 dpi equivalent |
| Copy Speed | 25 copies per minute (A4) |
| Scan Resolution | 600 dpi |
| Fax Resolution | 200 x 200 dpi, 300 x 300 dpi |
| Memory | 1 GB |
| Hard Disk Drive | 80 GB |
| Network Connectivity | Ethernet, USB |
| Scan Features | Scan to e-mail, Scan to FTP, Scan to SMB, Scan to USB Host, TWAIN scan |
Explanation of symbols used for safety warnings and prohibited/required actions.
Instructions for loading paper into the cassettes and multi-purpose tray.
Procedures for placing originals on the platen or in the document processor.
Steps for turning the machine's main power on and off.
Instructions for logging in and out of the machine when user login administration is enabled.
Step-by-step guide for performing basic copying operations.
Overview of sending scanned images via E-mail, PC, or Document Box.
Explains the functions and basic operations of the Document Box feature.
Procedure to specify the size of originals for scanning.
How to select the paper source for copying.
Enabling additional copies after a job is completed, with optional password protection.
Selecting the original size for scanning.
Selecting the size of the image to be sent.
Selecting the file format for sending scanned images.
Restricting access to PDF files by assigning passwords for display, print, or edit.
Creating, editing, and managing custom boxes for storing documents.
Information on Private Print, Stored Job, Quick Copy, and Proof and Hold Job Boxes.
Checking the status of jobs being processed or waiting to be printed.
Reviewing the history of completed jobs.
Pausing and resuming all printing jobs in printing/waiting status.
Suspending current job to prioritize a waiting job.
Checking toner, paper, and staple levels on the touch panel.
Configuring or checking the status of installed devices and lines.
Configuration of common settings like language, sound, and units.
Settings related to copying functions such as paper selection and zoom.
Adjusting print quality and performing machine maintenance procedures.
Resetting the machine's hard disk to its default mode.
Configuring network settings including host name and TCP/IP protocols.
Procedures for cleaning the machine's exterior and internal components.
Instructions for replacing toner containers and the waste toner box.
General guidelines for diagnosing and solving common machine problems.
How to respond to various alphanumeric error messages displayed on the touch panel.
Step-by-step instructions for clearing paper jams from different locations.
Specifies how user access is administered, including authentication methods.
Manages copy/print counts by assigning IDs to accounts.
Detailed technical specifications of the machine and its components.
To Next Page
