How to improve print clarity on Kyocera TASKalfa 250ci All in One Printer?
To improve print clarity on your Kyocera All in One Printer, select an appropriate image quality setting for the original document.
Why doesn't the Start key work on my Kyocera All in One Printer?
If pressing the Start key on your Kyocera All in One Printer doesn't produce copies, check for a message on the touch panel and respond accordingly. Also, if the machine is in Sleep mode, press the Power key to wake it up. It should be ready to copy within 45 seconds.
What to do if Kyocera TASKalfa 250ci finisher tray is full?
If the finisher tray of your Kyocera All in One Printer is full of paper, remove paper from the document finisher tray. If printing can be restarted, the touch panel display will prompt you to press [Continue]. Then press [Continue].
Why are documents printed improperly from my Kyocera TASKalfa 250ci All in One Printer?
If documents are printed improperly from your Kyocera All in One Printer, check that the printer driver and application software settings are set properly on your PC.
How to fix light printouts on Kyocera All in One Printer?
If your Kyocera All in One Printer prints are too light, try these solutions: * If in Auto Density mode, adjust the density level. * If in Manual Density mode, use [Image Quality] to set the correct density. * Shake the toner container from side to side. * Replace the toner container if prompted. * Replace the paper if it's damp. * Perform Drum Refresh or Laser Scanner Cleaning. * Disable EcoPrint mode.
Why are my Kyocera All in One Printer's printouts dirty?
If your Kyocera All in One Printer is printing dirty outputs, clean the platen or document processor. If that doesn't work, brush the transfer roller clean, carry out a Drum Refresh, or perform Laser Scanner Cleaning. Also, you can disable the Printed Document Guard Kit.
Why does my Kyocera All in One Printer keep jamming?
If paper often jams in your Kyocera All in One Printer, make sure the paper is loaded correctly. If it is, remove the paper, turn it over, and reload it. Also, replace the paper if it's curled, folded, or wrinkled. Finally, remove any jammed paper or loose scraps from the machine.
What to do if my Kyocera All in One Printer won't print?
If you cannot print from your Kyocera All in One Printer, ensure the power cord is plugged into an AC outlet and the main power switch is turned on. Verify the printer cable is securely connected, and if the machine was powered on before connecting the cable, power it on again after connecting the cable. If 'Press Status Key...' is displayed, press the Status/Job Cancel key, then [Printing Jobs], and [Resume All Print Jobs].
How to fix skewed images from Kyocera All in One Printer?
To resolve skewed images on your Kyocera All in One Printer, when placing originals on the platen, align them with the original size indicator plates. When using the optional document processor, align the original width guides securely before placing the originals. Also, check the position of the paper width guides to ensure the paper is loaded correctly.
Why does Kyocera TASKalfa 250ci All in One Printer stop copying and display 'Performing Color Calibration...'?
When your Kyocera All in One Printer stops copying and displays 'Performing Color Calibration...', the machine is carrying out a calibration process to ensure color stability. This is not a fault. Resume continuous copying when the calibration process ends.
General| Functions | Print, Copy, Scan, Fax |
|---|---|
| Copy Resolution | 600 x 600 dpi |
| Duplex Printing | Standard |
| Type | Color Multifunctional |
| Print Speed | 25 ppm |
| Print Resolution | 600 x 600 dpi, Multi-bit technology for print quality of 9, 600 x 600 dpi equivalent |
| Copy Speed | 25 copies per minute (A4) |
| Scan Resolution | 600 dpi |
| Fax Resolution | 200 x 200 dpi, 300 x 300 dpi |
| Memory | 1 GB |
| Hard Disk Drive | 80 GB |
| Network Connectivity | Ethernet, USB |
| Scan Features | Scan to e-mail, Scan to FTP, Scan to SMB, Scan to USB Host, TWAIN scan |
Explanation of symbols used for safety warnings and prohibited/required actions.
Instructions for loading paper into the cassettes and multi-purpose tray.
Procedures for placing originals on the platen or in the document processor.
Steps for turning the machine's main power on and off.
Instructions for logging in and out of the machine when user login administration is enabled.
Step-by-step guide for performing basic copying operations.
Overview of sending scanned images via E-mail, PC, or Document Box.
Explains the functions and basic operations of the Document Box feature.
Procedure to specify the size of originals for scanning.
How to select the paper source for copying.
Enabling additional copies after a job is completed, with optional password protection.
Selecting the original size for scanning.
Selecting the size of the image to be sent.
Selecting the file format for sending scanned images.
Restricting access to PDF files by assigning passwords for display, print, or edit.
Creating, editing, and managing custom boxes for storing documents.
Information on Private Print, Stored Job, Quick Copy, and Proof and Hold Job Boxes.
Checking the status of jobs being processed or waiting to be printed.
Reviewing the history of completed jobs.
Pausing and resuming all printing jobs in printing/waiting status.
Suspending current job to prioritize a waiting job.
Checking toner, paper, and staple levels on the touch panel.
Configuring or checking the status of installed devices and lines.
Configuration of common settings like language, sound, and units.
Settings related to copying functions such as paper selection and zoom.
Adjusting print quality and performing machine maintenance procedures.
Resetting the machine's hard disk to its default mode.
Configuring network settings including host name and TCP/IP protocols.
Procedures for cleaning the machine's exterior and internal components.
Instructions for replacing toner containers and the waste toner box.
General guidelines for diagnosing and solving common machine problems.
How to respond to various alphanumeric error messages displayed on the touch panel.
Step-by-step instructions for clearing paper jams from different locations.
Specifies how user access is administered, including authentication methods.
Manages copy/print counts by assigning IDs to accounts.
Detailed technical specifications of the machine and its components.
To Next Page
