LEM DX 26 PLUS - Factory PRESETS

61
Factory PRESETS
# Name Configuration Description Amplifiers
01 DEFAULT A135 B246 Default preset - routing = 3-WAY STEREO -
02 2X2W+MAX A13 B24 S56 2-WAY STEREO + 2 MONO FULL-RANGE OUT -
03 2X3W A135 B246 3-WAY STEREO -
04 2X3W+MSB+MAX A13 B24 S56 3-WAY STEREO with MONO SUB + 1 MONO FULL-RANGE OUT -
05 4W+2MAX A1234 S56 4-WAY MONO + 2 MONO FULL-RANGE OUT -
06 4W+BSB+2MAX A123 B4 S56 4-WAY MONO with B-SUB + 2 MONO FULL-RANGE OUT -
07 5W+MAX A12345 S6 5-WAY MONO + 1 MONO FULL-RANGE OUT -
08 5W+BSB+MAX A1234 B5 S6 5-WAY MONO with B-SUB + 1 MONO FULL-RANGE OUT -
09 6W A123456 6-WAY MONO -
10 6W+BSB A12345 B6 6-WAY MONO with B-SUB -
11 K6 A13 B24 S56 1 x K6 (for each side)
PFC3 (75W/8ohm)
PFC5 (500W/8ohm)
12 K6+KL A135 B246 1 x K6 + 1 x KL (for each side)
PFC3 (75W/8ohm)
PFC5 (500W/8ohm)
PFC5 (600W/8ohm)
13 K6+2xKL A135 B246 1 x K6 + 2 x KL (for each side)
PFC3 (75W/8ohm)
PFC5 (500W/8ohm)
PFC5 (1200W/4ohm)
14 K3 A13 B24 S56 1 x K3 (for each side)
PFC3 (50W/8ohm)
PFC3 (300W/8ohm)
15 K3+KL A135 B246 1 x K3 + 1 x KL (for each side)
PFC3 (50W/8ohm)
PFC3 (300W/8ohm)
PFC5 (600W/8ohm)
16 TM18 PR A135 B246 1 x TM18.3 MH + 1 x TM18.3 L (for each side)
PFC3 (90W/8ohm)
PFC3 (250W/8ohm)
PFC5 (1500W/4ohm)
17 TM18 FL A135 B246 1 x TM18.3 MH + 1 x TM18.3 L (for each side)
PFC3 (90W/8ohm)
PFC3 (250W/8ohm)
PFC5 (1500W/4ohm)
18 TM15 PR A13 B24 S56 1 x TM 15.2 (for each side)
PFC3 (90W/8ohm)
PFC5 (800W/8ohm)
19 TM15 FL A13 B24 S56 1 x TM 15.2 (for each side)
PFC3 (90W/8ohm)
PFC5 (800W/8ohm)
20 TM15+18 PR A135 B246 2 x TM15.2 + 1 x TM18.3 L (for each side)
PFC3 (180W/4ohm)
PFC3 (1500W/4ohm)
PFC5 (1500W/4ohm)
21 TM15+18 FL A135 B246 2 x TM15.2 + 1 x TM18.3 L (for each side)
PFC3 (180W/4ohm)
PFC3 (1500W/4ohm)
PFC5 (1500W/4ohm)
 IMPORTANT NOTE
The OUTPUT LEVEL and LIMITER THRESHOLD settings of the FACTORY PRESETS for LEM
enclosures have been made considering the OUTPUT POWER and INPUT SENSITIVITY
specifications of the LEM POWERFACTOR amplifiers in the CONSTANT GAIN (26dB) configuration.
Therefore, if amplifiers with different specifications are used, these parameters need to be
consequently adjusted.
Factory PRESET