Lenze E82EV752K4C - Total Index

Total index
2
Guide
2.3
L
2.3-1
EDS82EV903-1.0-11/2002
2.3 Total index
230 V controller, Mains connection, 6.4-4
400 V controller, Mains connection, 6.4-5, 6.6-4,
6.7-4, 6.8-4
87 Hz technology, 10.3-6
A
AC motor braking, 10.7-8
Acceleration, 10.7-1
Acceleration time
- Additional setpoint , 10.7-1, 10.20-20
- Minimum frequency limitation, 10.6-1, 10.20-21
- Process controller setpoint, 10.20-20
Acceleration times, 10.7-1
Accessories, 17.1-1
- External brake resistor, 13.4-1
- General, 17.2-1
- Type-specific, 17.3-1
Actual value, Digital supply, 10.8-9
Actual value selection, 10.8-1
- PID controller, 10.10-6
Adjustment
- Bipolar setpoint, 10.8-6
- Inverse setpoint, 10.8-7
- Unipolar setpoint, 10.8-6
Analog input 1
- Gain, 10.8-3, 10.20-9
- Offset, 10.8-3, 10.20-9
Analog input signals, 10.12-1
Analog inputs
- Automatic adjustment, 10.8-4, 10.20-43
- Gain, 10.8-3, 10.20-30
- Offset, 10.8-3, 10.20-30
Analog output 1
- Gain, 10.12-7, 10.20-12
- Offset, 10.12-7, 10.20-12
Analog output signals, 10.12-4
Analog outputs, Configuration, 10.12-4
Analog process data output words, Configuration,
10.12-10
Application, as directed, 1.4-1
Application as directed, 1.4-1
Application conditions, 9.3-1, 9.4-1
Application datum, Display, 10.16-1
Application examples, 15.1-1
Application I/O
- Acceleration times main setpoint, 10.7-1, 10.20-12
- Additional JOG values, 10.8-13, 10.20-43
- Automatic analog input adjustment, 10.8-4, 10.20-43
- Automatic frequency input adjustment , 10.8-10,
10.20-43
- Calibration of process variable, 10.16-3, 10.20-44
- Deceleration times main setpoint, 10.7-1, 10.20-12
- Delay digital outputs, 10.13-9, 10.20-41
- Main and additional setpoint, 10.20-19
- Offset analog outputs, 10.12-8, 10.20-41
- Output signal range - analog outputs, 10.12-8,
10.20-42
- Setpoint selection range, 8.6-5, 10.8-3, 10.20-9
- Terminal assignment, 7.2-9, 7.3-9, 7.4-9
Applicationexamples
- Dancer position control, 15.4-1
- Group drive, 15.6-1
- Operation of medium-frequency motors, 15.3-1
- Power control, 15.9-1
- Pressure control, 15.2-1
- Sequential circuit, 15.7-1
- Setpoint summation, 15.8-1
- Speed control, 15.5-1
Approvals, 4.2-1
Asynchronous standard motors, 1.4-1
Auto-TRIP reset, 11.5-1
Show/Hide Bookmarks