Lenze L-force E84A Series

To Next Page

To Previous Page

Electrical installation

StateLine C control terminals

Analog inputs and o utputs



227

EDS84ASC552 EN 10.0

Main Page

Table of Contents3
About this Documentation8
Document History8
Conventions Used9
Terms and Abbreviations Used10
Notes Used11
Safety Instructions12
General Safety and Application Notes for Lenze Controllers12
General Safety and Application Instructions for Lenze Motors15
Residual Hazards18
Product Description19
Device Features19
Overview of Standard Devices20
Overview of Control Terminals23
Identification25
Product Key26
Technical Data27
General Data and Operating Conditions27
Rated Data33
Overview33
Operation at Rated Mains Voltage 230 V36
Operation at Rated Mains Voltage 400 V40
Operation at a Rated Mains Voltage of 500 V47
Operation with Increased Power at a 230 V Mains54
Operation with Increased Power at a 400 V Mains57
Operation with Increased Power at a 500 V Mains62
Current Characteristics67
Overcurrent Operation71
Terminal Description73
Overview73
Stateline C Control Terminals77
External Supply Voltage77
Analog Inputs78
Analog Outputs78
Digital Inputs79
Digital Outputs79
Connection of Relay Output79
Highline C Control Terminals80
External Supply Voltage 24 V80
Analog Inputs81
Analog Outputs81
Digital Inputs82
Digital Outputs82
Connection of Relay Output82
Motor Holding Brake Connection83
Topline C Control Terminals84
Axis Bus84
Multi-Encoder Connection85
Resolver Connection87
Mechanical Installation88
Important Notes88
Standard Devices in a Power Range of 0.2589
Assembly in Built-In Technique (Standard)89
Assembly in Push-Through Technique (Thermal Separation)98
Mounting in "Cold Plate" Technique103
Standard Devices in the Power Range 3112
Assembly in Built-In Technique (Standard)112
Assembly in Push-Through Technique (Thermal Separation)121
Mounting in "Cold Plate" Technique129
Standard Devices in a Power Range of 30138
Assembly in Built-In Technique (Standard)138
Mounting in "Cold Plate" Technique148
Electrical Installation153
Important Notes153
Electrical Isolation157
Device Protection158
Maximum Motor Cable Length159
Motor Protection159
Interaction with Compensation Equipment159
Safety Instructions for the Installation According to UL or UR160
Safety Instructions for the Installation According to UL or UR164
Installation According to EMC (Installation of a CE-Typical Drive System)168
Shielding168
Mains Connection, DC Supply170
Motor Cable171
Control Cables172
Installation in the Control Cabinet173
Wiring Outside of the Control Cabinet175
Detecting and Eliminating EMC Interferences177
Devices in the Power Range 0.25178
Example Circuits178
Terminal Assignment of the Power Connections182
Devices in the Power Range 0.37189
Example Circuits189
Terminal Assignment of the Power Connections192
Devices in a Power Range of 30201
Example Circuits201
Terminal Assignment of the Power Connections202
Common Control Terminals211
Important Notes211
System Bus Connection (Canopen)215
Connection of Relay Output221
Diagnostics223
Stateline C Control Terminals224
External Supply Voltage 24 V224
Analog Inputs and Outputs225
Digital Inputs and Outputs228
Highline C Control Terminals230
External Supply Voltage 24 V230
Analog Inputs and Outputs232
Digital Inputs and Outputs235
Motor Holding Brake Connection238
Topline C Control Terminals239
Resolver Connection239
Encoder Connection240
Axis Bus241
Commissioning243
Before Switching on243
Quick Commissioning246
Keypad Control247
Terminal Control249
Braking Operation251
Braking Operation Without Additional Measures251
Braking Operation with External Brake Resistor252
Operation at Rated Mains Voltage 230 V252
Operation at Rated Mains Voltage 400 V253
Operation at a Rated Mains Voltage of 500 V254
Selection of the Brake Resistors255
Rating for Lenze Brake Resistors256
Wiring of Brake Resistor258
Operation with Spring-Applied Brake260
Introduction260
Rated Data262
Wiring264
Diagnostics267
Display of Operating Data, Diagnostics267
Status Display Via Controller Leds267
Drive Diagnostics Via Keypad270
Safety Engineering272
Introduction272
Important Notes273
Hazard and Risk Analysis274
Standards274
Mission Time275
Acceptance276
Description276
Periodic Inspections276
Basics for Safety Sensors277
Operating Mode278
Hardware Revision280
Technical Data281
Electrical Installation285
Certification287
Accessories (Overview)288
Overview288
Mains Chokes289
RFI Filter/Mains Filter291
Sinusoidal Filters293
External Brake Resistors294
Memory Module295
E84Aym10S295
Communication Modules296
Keypad297
Power Supply Units298
Terminals (Replacement)299
EMC Accessories301
Accessories for Applications with Digital Frequency304
Appendix305
Total Index305

Lenze L-force E84A Series - Page 227

Table of Contents

Related product manuals