Connect ID 32-46 - 24 -
Operating instructions
Setting options for DVB-C reception:
If you have not selected a DVB-C antenna in the antenna selection: Con-
tinue with Setting options for DVB-S reception (see right hand column).
If several networks are available over DVB-C, you can
decide which network you want to receive your channels
from. The normal DVB-C settings are derived from the
selection of the location or network and do not need
to be changed. Exactly which of the following settings
are present is dependent on which network is selected.
Select network,
OK Proceed.
Select and adapt settings for DVB-C reception.
You can state whether coded stations are to be searched
for in the search/update.
Select yes to save all found
scrambled stations. However, these stations can only be
received in connection with a CA module and the
appropriate Smart Card.
Handling of the CA module is
described on page 63.
If a CA module with a SmartCard is already plugged in
for the station search, all the stations which this module
can descramble are also saved when no is preset.
If you want to run the station search independently of
the channel grid, select frequency search for the search
method.
The DVB stations are only searched for in the frequency
range above the start frequency.
Only change these defaults if you are familiar with other
symbol rates and types of modulation or if you have to
specify the network ID for your cable network. In the
case of small cable networks fed directly from the satel-
lite, the rate of 6900 might have to be replaced by 6111.
Your cable provider has the information you need.
OK Proceed.
Network
selection
Settings
Encrypted
stations
Search
method
Start
frequency
Network ID
Symbol rate
QAM
modulation
OK
INITIAL INSTALLATION (DVB-C)
Scrambled stations no yes
Search method Channel search
Start frequency 047.0 MHz
Network ID none
Symbol rate 1 (DVB-C) 6875
Symbol rate 2 (DVB-C) 6900
QAM modulation 1 64
QAM modulation 2 256
Proceed
Setting options for DVB-S reception:
If you have not selected a DVB-S antenna in the antenna selection:
Continue with Setting options for all types of reception on page 28.
The normal DVB-S settings are derived from the selection
of the location and do not need to be changed in most
cases.
Selecting the satellite system.
Specify how you receive which satellite(s) (single
satellite or type of satellite system). Ask your
dealer if required.
Reception of a single satellite via a connected LNC (LNB).
See page 25 for settings.
Reception of two different satellites with two LNCs
(LNBs) which are connected to the TV set by a 22 kHz
switchbox. See page 25 for settings.
Reception of two different satellites with two LNCs
(LNBs) which are connected to the TV set by a toneburst
switch. See page 25 for settings.
The TV set controls a DiSEqC multiswitch to which up
to four LNCs (LNBs) for different satellites are connect-
ed. See page 26 for settings.
Select setting if the TV set is connected to a DiSEqC
single-cable system (according to EN 50494). Several
Sat receivers can be connected to one Sat cable. See
page 26 for settings.
Select setting if the TV set is connected to a single-cable
system (without DiSEqC). Several Sat receivers can be
connected to one Sat cable. Unlike a DiSEqC single-cable
system there are restrictions in the range of certain
reception frequencies in single-cable community
systems. See page 27 for settings.
OK Proceed
(to the appropriate page of the satellite system).
OK
OK
INITIAL INSTALLATION (DVB-S)
Select satellite installation
Single satellite
2 satellites on 22 kHz switchbox
2 satellites on toneburst switch
Max. 4 satellites on DiSEqC multiswitch
DiSEqC one cable communal system
other communal installation
Proceed Back
Initial installation
Select
satellite
installation
Single
satellite
2 satellites
on 22 kHz
switchbox
2 satellites
on toneburst
switch
Max. 4
satellites
on DiSEqC
multiswitch
DiSEqC
one cable
communal
system
other
communal
installation
To Next Page