Home
Meggitt
Protection Device
vibro-meter VM600
Meggitt vibro-meter VM600 Quick Start Manual
5
of 1
of 1 rating
88 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
QUICK STAR
T MANU
AL
Document reference MAVM600MK2M
PS-QS/E
VM600
Mk2
mach
inery
protecti
on system
(MPS)
Edit
ion 2 -
February 2
021
ii
THIS PAGE INTENTIONALLY LEFT BLANK
3
5
Table of Contents
Revision Record Sheet
2
Important Notices
3
Preface
5
Safety
9
Table of Contents
13
1 Introduction to the Vm600 Machinery Protection System (Mps)
18
System Overview
18
Installing a Rack
19
Ventilation
21
Circuit Breaker
24
Supply Wiring
25
Instructions for Locating and Mounting
26
Connecting Power
27
Front Panels
28
Associated Rear Panels
29
Power Supply Check Relay
29
Handling VM600 Mk2 Modules
29
Installing VM600 Mk2 Modules
29
VM600 Mk2 /VM600 Rack Slots / Module Positions
30
Installation Restrictions
31
Communicating with a VM600
33
Mps
33
Connecting to a Computer
35
Software Configuration
35
Hardware Configuration
36
Vibrosight Networking
37
Zero-Configuration Networking
37
Vibrosight Network Requirements
38
Wide Area Networking
38
Mpc4 + Ioc4
38
MPC4 Mk2 + IOC4 Mk2 Module
38
Identifying a MPC4 Mk2 + IOC4 Mk2 Module in a Configuration
40
Hardware
41
VM600 Racks
41
VM600 System Racks (Abe04X)
41
VM600 Slimline Racks (ABE056)
41
MPC4 Mk2 Machinery Protection and Condition Monitoring Module
45
MPC4 Mk2 Module Leds
46
MPC4 Mk2 Module Buttons
51
MPC4 Mk2 Module Factory Assigned Defaults
52
MPC4 Mk2 Module as a Spare Part
52
MPC4 Mk2 Module as Part of a VM600 Mk2 Solution
52
IOC4 Mk2 Input/Output Module
54
IOC4 Mk2 Module Connector Pinouts
56
RLC16 Mk2 Relay Module
62
Rlc16
62
Rlc16
64
Connecting Sensors/Measurement Chains to a VM600 Mk2 MPS
70
Software
71
Vibrosight System Manager
71
Vibrosight Protect
71
Common Vibrosight System Manager Tasks
72
Configuring the Network Interface for a MPC4 Mk2 Module
72
Notes on Configuring the IP Settings for a MPC4 Mk2 Module
74
Identifying a MPC4 Mk2 Module in a VM600 Mk2 /VM600 Rack Using
74
Vibrosight System Manager
74
Changing the Firmware for a MPC4 Mk2 Module
77
Notes on Changing the Firmware for a MPC4 Mk2 Module
78
Common Vibrosight Protect Tasks
79
Configuration
79
Identifying a MPC4 Mk2 Module in a VM600 Mk2 /VM600 Rack Using
80
Vibrosight Protect
80
4 Mpc4
81
Module
82
MPC4 Mk2 Module Firmware
82
MPC4 Mk2 Module Operating Modes
84
Power-Up Mode
84
Operational Mode
84
Fail-Safe Mode
85
Recovery Mode
85
Mps
86
5 Service and Support
87
Contacting Us
87
Technical Support
87
Sales and Repairs Support
87
Repairs and Returns
88
End-Of-Life Product Disposal
88
Other manuals for Meggitt vibro-meter VM600
Hardware Manual
382 pages
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Meggitt vibro-meter VM600 and is the answer not in the manual?
Ask a question
Meggitt vibro-meter VM600 Specifications
General
Brand
Meggitt
Model
vibro-meter VM600
Category
Protection Device
Language
English
Need help?
General
To Next Page
