Need help?Do you have a question about the Miele H350 and is the answer not in the manual?
Details the components of the H 350 oven unit, illustrated with a diagram.
Details power requirements and wiring connections for oven installation.
Instructions for initial oven setup, including cleaning and first heating cycle.
Explains the oven's program selector and push buttons with corresponding symbols.
Guide to cooking using default temperatures, including setting time and end-of-cycle notifications.
Details the rapid heat feature and how to disable it for specific cooking needs.
Details the functions activated by different selector switch programs (Convection, Surround, etc.).
Explains the cooling fan's operation after the oven cools down to prevent condensation.
Details the catalyser system for H387 models and its function.
Details the thermal cleaning process, heating, door lock, and duration for H387 models.
Describes the catalyser components and its function during exhaust air cleaning.
Explains automatic oven shut-off based on operating time and mode, with fault code information.
How the door switch signals the control unit to affect fan and heater operation.
Describes the platinum temperature sensor and its resistance behavior.
Details the door lock mechanism after pyrolitic cycle completion.
Explains how the door contact switch affects fan, heating, and cooling fan speed.
Describes the combined control and power electronics unit and its monitored/controlled components.
Diagram and list of electrical components for the H-350 model.
Diagram and list of electrical components for the H-373 model.
Diagram and list of electrical components for the H-387 model.
Step-by-step procedure for removing the oven door.
Procedure for removing the oven from its housing.
Procedure for removing the front cover of the oven.
Procedure for removing the oven's fascia panel.
Procedure for removing the control module.
Procedure for removing the control and power module.
Procedure for removing the rear cover.
Procedure for removing the rear panel.
Procedure for removing the left or right side panel.
Procedure for removing the left or right deflector strip.
Procedure for removing the door hinge bearing.
Procedure for removing the cleanglass door panel.
Procedure for removing the middle door glass.
Procedure for installing the oven door.
Procedure for removing and replacing the halogen lamp.
Procedure for removing the shelf runner.
Procedure for removing the reflector and glass cover.
Procedure for removing the cavity rear panel.
Procedure for removing the upper heater element.
Procedure for removing the lower heater element.
Procedure for removing the oven temperature sensor.
Procedure for removing the temperature regulator.
Procedure for removing the convection heating element.
Procedure for removing the convection heating fan.
Procedure for removing the fumes extractor.
Procedure for removing the cooling fan.
Procedure for removing the catalyser component from pyrolitic/self-cleaning models.
Procedure for removing the catalyser temperature sensor from pyrolitic/self-cleaning models.
Procedure for releasing the door latch on pyrolitic/self-cleaning models.
Procedure for removing the door lock cable on pyrolitic/self-cleaning models.
Procedure for removing the door switch.
Procedure for removing the door locking device on pyrolitic/self-cleaning models.
Procedure for removing the temperature regulator on pyrolitic/self-cleaning models.
Procedure for manually overriding the door lock mechanism.
Instructions for accessing and navigating the oven's service modes for diagnosis.
Details common fault codes, their causes, and remedies.
Details the cause (short-circuited roast probe) and remedy for Fault Code F3.
Details the cause (open-circuited oven PTC sensor) and remedy for Fault Code F4.
Details the cause (short-circuited oven PTC sensor) and remedy for Fault Code F5.
Details the cause (safety cutouts tripped) and remedy for Fault Code F6.
Details the cause (high electronic temp due to poor ventilation/fan) and remedy for Fault Code F9.
Details causes (defective drive, cable, regulator) and remedies for Fault Code F13.
Details causes (defective drive, cable, regulator) and remedies for Fault Code F14.
Details causes (soiling, defective elements/catalyser) and remedies for Fault Code F15.
Details the cause (model variant deleted) and remedy (reprogram) for Fault Code F16.
Details the cause (open-circuited catalyser sensor) and remedy for Fault Code F17.
Provides troubleshooting steps for common oven faults and repairs.
Addresses excessive noise from the convection fan, identifying causes and remedies.
Addresses unit heating to higher temps than selected due to software faults.
Addresses loud operational noises from cooling fans, noting unknown cause and modifications.
Explains misting between door glass panels due to ambient moisture and dirt.
Addresses condensation on the timer and digital display from food moisture.
Diagnoses why the oven does not heat and the fan doesn't operate, focusing on the door contact switch.
Troubleshoots the issue where the pyrolitic cleaning cannot be stopped.
Guides on programming model number, operating parameters, and supply voltage.
Instructions for displaying the programmed model variant, e.g., H 01.
Instructions for displaying the oven's electronic software version.
Activates the cooling fan at high speed for baking.
Activates the cooling fan at low speed for run-on operation.
Activates the convection fan at maximum speed.
Activates the convection fan at minimum speed.
Activates the oven lights.
Performs a check of all oven display segments and segments.
Activates the oven's buzzer.
Displays the actual temperature detected by the roast probe.
Activates the cooling fan at pyrolitic cleaning speed.
Activates the door lock motor.
Activates the demonstration mode where heating elements cannot be turned on.
Deactivates the demonstration mode.
Retrieves and deletes detected fault codes, activates child-safety feature.
Displays the operating hours for Fan Heat and Auto Roast modes.
Displays the operating hours for Convection Heating mode.
Displays operating hours for heating elements, activates child-safety feature.
Displays the regulator parameter, noting it can only be modified via service mode 31.
Sets the electrical frequency, noting it can only be modified via service mode 31.
Overview of accessing and navigating the programming mode for various functions.
Sets the oven to the standard setting, allowing modification of mode and temperature.
Activates the oven lock, preventing alteration of selected mode and temperature.
Configures the oven light to activate when an operating mode is selected.
Configures the oven light to activate whenever the door is opened.
Sets the display format for temperature and time to 12 or 24-hour clock.
Configures oven light behavior: turning off after 15 seconds or staying on.
Configures Rapid Heat feature: standard (on) or optional (off).
Adjusts clock display for advancing or setting back time in 1-hour increments.
Configures buzzer: standard (on) or optional (off) at end of cooking cycle.
To Next Page
General