Chapter 1 Before Use
1-11
1
2
2
2
5
6
Caution in handling of ink cartridges
Media
Usable media sizes and notes for handling are described.
Usable sizes of media
Caution in handling of medias
Pay attention to the followings for handling of medias.
• Before using ink and cleaning solution, be sure to
read the Safety Data Sheet (SDS).
• Keep ink away from fire. Also, be sure that the
room is well ventilated when using or handling ink.
• If you get ink in your eyes, immediately wash your
eyes with a plenty of clean water for at least 15
minutes. and then rinse thoroughly to the back of
your eyelids. Also, see a doctor as soon as
possible.
• If you accidentally swallow ink, rest and seek
medical attention immediately. Do not allow him or
her to swallow the vomit. Then contact the
emergency number written in SDS.
• If you inhale a lot of vapor and feel bad,
immediately move to a location of fresh air and
then keep yourself warm and quiet. Also, see a
doctor immediately.
• If the ink adheres to your skin, wash it off
thoroughly with a large amount of water and soap
or skin cleanser.
• Safety is evaluated by our recommended ink.
Please use our recommended ink for safe use.
• If the ink cartridge is moved from a cold place to a
warm place, leave it in the room temperature for
three hours or more before using it.
• Open the ink cartridge just before installation. If
the ink is left open for a long time, normal printing
performance may not be ensured.
• Make sure to store ink cartridges in a cool and
dark place.
• Keep ink cartridges and waste ink tank out of
reach of children.
• Be sure to thoroughly consume the ink cartridge
within 3 months after opening it. If it has passed
for a long time after opening, the print quality
would be poor.
• When you no longer need ink cartridges, ink
packs, and waste ink, please hand them over to
your distributor or service representative. If you
dispose them by yourself, please followthe
regulations stipulated by the industrial waste
disposer or the local regulations of each country.
• Do not hit the ink cartridge strongly or shake it
violently. Ink may leak from the cartridge.
• Do not refill ink in the ink pack or ink cartridge. We
are not responsible for any problems caused by
using refilled ink.
• Do not touch or stain the contact area of the ink
cartridge PCB. It may cause a PCB failure.
• Do not disassemble the ink cartridges.
Model
JV300-
130A
JV300-
160A
JV300-
130A Plus
JV300-
160A Plus
Type of
Recommended
media
Photo-paper/ Synthetic paper/
Duplex paper
Maximum width 1371mm 1620mm 1371mm 1620mm
Minimum width 210mm 210mm 210mm 210mm
Maximum
printing width
1361mm
1610mm
*1
*1. When "MARGIN(RIGHT/LEFT)" in the Setup menu has been
set to the minimum (-10 mm).
1361mm
1610mm
*1
Roll media
Thickness 1.0mm or less
Roll outside
diameter
Φ250mm or less (paper media)
Φ210mm or less (others)
Roll weight 40kg or less 45kg or less
Roll inside
diameter
3 or 2 inches
Side printed Side facing outward
• Use recommended media.
Use our recommended media to print with stable
and high image quality.
• Pay attention to the expansion and contraction of
the media.
Do not use media that has just been opened. The
media may expand and contract depending on
the room temperature and humidity. Open the
package and expose it to the place of use for at
least 30 minutes before attaching it to the unit.
• Do not use curled media.
In addition to causing media jams, it also affects
the image quality.
Also, use media with tight curls after removing the
curls. If a regular-sized coated sheet of media is
rolled and stored, the coated side has to face
outside.
• Be careful to dusts on the edge face of the media.
Some rolls have dusts contained in the package
gathered on the edge surface of the roll. If you
use as it is, the drawing quality may be degraded
due to nozzle missing or ink drops. Be sure to set
the roll after removing dusts adhering on the edge
face of the roll.
To Next Page
Loading...
