Mitsubishi Electric MELSEC iQ-R Series - Page 613

36 ERROR CODES
36.4 List of Error Codes
611
36
413DH File related error • The specified file capacity cannot be secured. • Execute again after increasing the capacity of the specified
drive (memory).
413EH File related error • Operation is disabled for the specified drive
(memory).
• Execute again after changing the target drive (memory).
413FH File related error • The file is inhibited to be written to the file storage
area.
• Execute again after changing the specified drive (memory).
414AH Intelligent function module
specification error
• In a multiple CPU system, operation was
performed to a non-controlled intelligent function
module or network module.
• Execute the operation again from the control CPU of the
target module.
414CH Intelligent function module
specification error
• The specified buffer memory address cannot be
accessed.
• Execute again after checking the buffer address.
4150H File related error • An attempt was made to initialize the drive
(memory) protected by the system.
• Do not initialize the target drive (memory) as it cannot be
initialized.
4151H File related error • An attempt was made to delete the file/folder
protected by the system.
• Do not delete the target file as it cannot be deleted.
4160H Online registration error • The registered number of I/O devices of the
forced on/off target exceeded the maximum.
• Cancel the registration of I/O devices of the forced on/off
target that is not used.
4168H Online registration error • The number of registered settings of the device
test with execution conditions has exceeded 32.
• Disable the settings of the device test with execution
conditions registered in the CPU module. Alternatively,
reduce the number of executional conditioned device tests to
be registered at a time.
4169H Online registration error • No settings of the device test with execution
conditions are registered.
• Check the number of registered settings of the device test
with execution conditions in the CPU module, and disable the
settings.
416AH Online registration error • The specified execution conditions do not exist.
(Device test with execution conditions)
• Check whether the execution conditions (program block, step
No., and execution timing) specified for disabling settings are
registered in the CPU module.
416BH Online registration error • Other than the ladder program was specified for
the registration of the device test with execution
conditions.
• Check and correct the program block specified when the
settings of the device test with execution conditions are
registered or disabled.
41C1H File related error • The format information data of the specified drive
(memory) is abnormal.
• The file information data may be corrupted.
• Back up data in the CPU module, and then initialize the
memory.
41C2H File related error • File open specification data for file access is
wrong.
• Execute again after checking the specification data.
41C3H File related error • Simultaneously accessible files exceeded the
maximum.
• Execute again after decreasing file operations.
41C4H File related error • Simultaneously accessible files exceeded the
maximum.
• Execute again after decreasing file operations.
41C5H File related error • The specified file does not exist.
■When CPU Module Logging Configuration Tool is
used
When an attempt was made to re-register the data
logging with the previous settings, the
corresponding file did not exist.
• Execute again after checking the file.
41C7H File related error • The specified file/folder or drive (memory) does
not exist.
• Execute again after checking the file/folder or drive
(memory).
41C8H File related error • The size of the specified file has exceeded that of
the existing file.
• Execute again after checking the size of the specified file.
• If the error recurs after re-execution, the file information data
may be corrupted.
• Back up data in the CPU module, and then initialize the
memory.
41C9H File related error • Access to the file sector has failed.
• The format information data of the target drive
(memory) is abnormal.
• Back up data in the CPU module, and then initialize the
memory.
41CAH File related error • Access to the file sector has failed.
• The format information data of the target drive
(memory) is abnormal.
• Back up data in the CPU module, and then initialize the
memory.
41CBH File related error • The file name is specified in a wrong method. • Execute again after checking the file name.
Error
code
Error name Error details and cause Action