Mitsubishi Electric MELSEC iQ-R - Page 247

3 TROUBLESHOOTING
3.5 Message Log List
245
3
Unicast Sock setsockopt Error Major error The specified unicast IP address was not
set for the BACnet module.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Unicast Sock
SO_REUSEADDR,SO_REUSEADDR Error
Major error The specified unicast IP address was not
set for the BACnet module.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Unicast Sock Bind Error Major error The specified unicast IP address was not
set for the BACnet module.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Broadcast Sock getaddrinfo XXXXXX Error Major error The IP address of the specified broadcast
was not set for the BACnet module.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Unicast=IPV6 Broadcast != IPV6 Error Major error The unicast address was set in IPv6, but a
broadcast address was not set in IPv6.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Broadcast setsockopt
IPPROTO_IPV6,IPV6_ADD_MEMBERSHIP
XXXX InterfaceNo=YY Error
Major error An option for the IPv6 broadcast socket was
not set.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Broadcast setsockopt
IPPROTO_IPV6,IPV6_MULTICAST_HOPS
XXXX hop=YY Error
Major error An option for the IPv6 broadcast socket was
not set.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
BroadCast Socket Error Major error The IP address of the specified broadcast
was not set for the BACnet module.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Broadcast Sock setsockopt
SO_BROADCAST Error
Major error The IP address of the specified broadcast
was not set for the BACnet module.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Broadcast Sock setsockopt
SO_REUSEADDR Error
Major error The IP address of the specified broadcast
was not set for the BACnet module.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Broadcast Sock Bind Error Major error The IP address of the specified broadcast
was not set for the BACnet module.
• Review the setting of the IP address.
• Turn the power OFF and ON, or reset the
CPU module.
• If the same message appears even after
taking the above corrective actions, initialize
or replace the BACnet module.
Message log Log level Message detail Corrective action