Nice Spido Instructions And Warnings For Installation And Use

32 – ENGLISH
Table 21
INCORPORATED RADIO RECEIVER TECHNICAL SPECIFICATIONS
Description Technical specication
Product type 4-channel receiver for incorporated radio remote control
Frequency 433.92 MHz
Encoding Digital rolling code 72-bit Opera type
Transmitter compatibility Supported protocols: O-Code
Memorisable
transmitters
Up to 90 if memorised in Mode 1
Input impedance 52 Ω
Sensitivity Better than 0,5 µV
Transmitter range
From 100 to 150 m. This range can vary if there are obstacles and electromagnetic disturbances, and depends
on the position of the receiving antenna
Outputs -
Operating temperature
(min/max °C)
-20°C ... +55°C
Table 22
GUIDE TECHNICAL SPECIFICATIONS
Description SR32C SR16C SR08C SR32B SR16B SR08B SR40B
Product type
single
galvanised
steel prole
2-piece
galvanised
steel prole
single
galvanised
steel prole
single
galvanised
steel prole
2-piece
galvanised
steel prole
single
galvanised
steel prole
2-piece
galvanised
steel prole
Guide length 3200 mm
3200 (1600x2)
mm
800 mm* 3200 mm
3200 (1600x2)
mm
800 mm* 4000 mm*
Useful stroke 2800 mm 2800 mm 3500 mm** 2800 mm 2800 mm 3500 mm** 3500 mm**
Guide height 30 mm 30 mm 30 mm 30 mm 30 mm 30 mm 30 mm
Belt height - - - 10 mm 10 mm 10 mm 10 mm
Belt/chain length 6185 mm 6185 mm 7747 mm 6180 mm 6180 mm 7720 mm 7856 mm
* To be used with a 3.2 m guide to reach a length of 4 m.
** Data referred to the 4 m guide.
CONFORMITY
13
13 CONFORMITY
EU Declaration of Conformity
and declaration of incorporation of “partly completed machinery”
Note - The contents of this declaration correspond to declarations in the ofcial document deposited at the registered ofces of Nice S.p.a. and in particular to the last revision available before
printing this manual. The text herein has been re-edited for ed
itorial purposes. A copy of the original declaration can be requested from Nice S.p.a. (TV) I.
Number:
713/SPIDO600 Rev: 1 Language: EN
Manufacturer’s Name:
Nice s.p.a.
Address:
Via Callalta 1, 31046 Oderzo (TV) Italy
Authorized Person to constitute
technical documentation:
Nice s.p.a.
Type of product:
Gearmotor for doors automation
Model/Type:
SPIDO600
Accessories:
Refer to the catalog
The
undersignedRobertoGriffa,intheroleofChiefExecutiveOfcer,declaresunderhissoleresponsibilitythattheproductdescribedabovecomplieswiththe
provisions
laid
downinthefollowingdirectives:
•Directive
2014/53/EU(RED),accordingtothefollowingharmonizedstandards:Healthprotectionstandards(art.3(1)(a))EN62479:2010,Electricalsafety(art.
3(1)(a))
EN62368-1:2014+A11:2017, Electromagnetic compatibility (art. 3(1)(b)) EN 301 489-1 V2.1.1:2017, EN 301 489-3 V2.1.1:2017,
Radio spectrum (art. 3(2)) EN 300 220-1 V3.1.1:2017, EN 300 220-2 V3.2.1:2018.
•
Directive 2011/65/UE (RoHS II)
The
productalsocomplieswiththefollowingdirectivesaccordingtotherequirementsenvisagedfor“partlycompletedmachinery”(AnnexII,part1,sectionB):
•
Directive 2006/42/EC of the EUROPEAN PARLIAMENT AND COUNCIL of 17 May 2006 related to machinery and amending the Directive 95/16/EC (recast).
It
isherebystatedthattherelevanttechnicaldocumentationhasbeencompiledinaccordancewithannexVIIBofDirective2006/42/ECandthatthefollowing
essential
requirements
havebeenfullled:1.1.1-1.1.2-1.1.3-1.2.1-1.2.6-1.5.1-1.5.2-1.5.5-1.5.6-1.5.7-1.5.8-1.5.10-1.5.11
The
manufacturerundertakestotransmittothenationalauthorities,inresponsetoareasonedrequest,therelevantinformationonthe“partlycompletedmachinery“,
while
maintaining full rights to the related intellectual property.
Should
the“partlycompletedmachinery”beputintoserviceinaEuropeancountrywithanofciallanguageotherthanthatusedinthisdeclaration,theimporteris
obliged
to arrange for the relative translation to accompany this declaration.
The
“partlycompletedmachinery”mustnotbeuseduntilthenalmachineinwhichitisincorporatedisinturndeclaredascompliant,ifapplicable,withtheprovisions
of
directive 2006/42/EC.
The
productalsocomplieswiththefollowingstandards:
N 60335-1:2012 + A11:2014 + A13:2017 + A1:2019 + A2:2019 +A14:2019, EN 60335-2-103:2015, EN 62233:2008, EN 61000-6-2:2019, EN 6
1000-6-3:2007+A1:2011
Oderzo,
02/03/2021
Ing. Roberto Griffa
(ChiefExecutive
Ofcer)

Nice Spido Specifications