Need help?Do you have a question about the Nikon Eclipse LV100DA-U and is the answer not in the manual?
Explains symbols used on the product, including a "Caution for heat" marking.
Specifies intended use and warns against disassembling the microscope to prevent hazards.
Details power supply ratings and power cord specifications for safe operation.
Lists compatible light sources and accessories for the microscope system.
Addresses usage of external light sources and potential UV light exposure hazards.
Warns about heat from the light source and the importance of clear air vents.
Cautions regarding safe operation of motorized components to prevent injury.
Emphasizes careful handling, avoiding moisture, and electromagnetic wave interference.
Guidelines for proper installation location and safe methods for moving the microscope.
Cautions during assembly, lens care, and lamp replacement procedures.
Notes on handling filter cubes and the necessity of software setup after assembly.
Diagrams and labels identifying components on the front left and right sides of the microscope.
Details the functions of the operation panel and the various connectors.
Diagrams and labels identifying components on the rear of the microscope.
Explains the initial setup using LVSetup and how interlock control affects microscopy.
A list and summary of available microscopy methods and required accessories.
Step-by-step guide for setting up bright-field microscopy with epi illumination.
Procedures for specimen focus, brightness adjustment, and eyepiece settings.
Steps for setting up dark-field microscopy and returning to bright-field.
Procedures for setting up polarization microscopy and returning to bright-field.
Setup procedures for Senarmont method DIC microscopy.
Setup procedures for Prism Slide method DIC microscopy.
Steps to revert to bright-field microscopy after DIC observation.
Steps to configure the microscope for epi-fl microscopy.
How to return to bright-field or dark-field from epi-fl microscopy.
Step-by-step guide for setting up bright-field microscopy with diascopic illumination.
Procedures for specimen focus and observation in diascopic bright-field.
Steps for setting up polarization microscopy with diascopic illumination.
How to return to bright-field microscopy from diascopic polarization.
Steps for setting up dark-field microscopy with diascopic illumination.
How to return to bright-field microscopy from diascopic dark-field.
Steps for setting up phase contrast microscopy with diascopic illumination.
How to return to bright-field microscopy from diascopic phase contrast.
Steps for setting up DIC microscopy with diascopic illumination.
How to return to bright-field microscopy from diascopic DIC.
Detailed steps for powering the microscope on and off, including initialization.
Procedures for operating external power supplies and light sources.
Guide for initial setup using LVSetup software and PC connection.
How to switch between episcopic and diascopic illumination using panel switches.
How to select different microscopy methods using the CUBE switch for epi illumination.
A table summarizing episcopic microscopy methods with details.
A table summarizing diascopic microscopy methods with details.
Explains interlock control linking devices to microscopy and objective settings.
How to modify and reset user offset settings for illumination and aperture.
Using EPI and DIA switches for illumination control and brightness.
Operating external sources and the antiglare function.
Using brightness switches and interlock controls for illumination brightness.
How to rotate the nosepiece, interlock control, and switching restrictions.
Lists and describes filters for both episcopic and diascopic illumination.
How to operate the stage, use glass slide holders, and center the stage.
Details coarse/fine focus knobs, stiffness adjustment, and stopper function.
Optical path selection, adapter use, and eyepiece tube centering.
Procedures for adjusting eyepiece diopters and interpupillary distance.
Adjusting the field diaphragm for specimen illumination and centering.
Adjusting the aperture diaphragm for resolution/contrast and centering.
How interlock control affects the aperture diaphragm and how to reset settings.
Steps for focusing and centering the condenser for diascopic illumination.
Adjusting field and aperture diaphragms for diascopic illumination.
Operating slide and universal condensers, and selecting condenser modules.
Details on types and usage of polarizer sliders for episcopic illumination.
How to attach and adjust polarizers for diascopic illumination.
Steps for placing, removing, and orienting the analyzer slider.
Explains the PA block's function, structure, and installation.
Steps for inserting and removing the lambda plate slider for episcopic illumination.
Steps for attaching and operating the lambda plate slider for diascopic illumination.
Selecting, attaching, and setting up DIC prisms for Senarmont method.
Selecting, attaching, and setting up DIC prisms for Prism Slide method.
Selecting and installing DIC prisms for diascopic illumination.
Table showing optimal prism combinations with objectives for contrast/resolution.
Details on filter cubes, light sources, and EX/BA filter selection for epi-fl microscopy.
How to use the excitation light balancer and its objective compatibility.
Warnings and cautions before starting assembly and the importance of software setup.
Lists assembly tools and guidelines for selecting an installation location.
Lists compatible illuminators and light sources, noting UL listing.
Instructions for attaching various stage types, glass holders, and condenser plates.
Steps for attaching and selecting the appropriate condenser based on stage type.
Steps for attaching the motorized nosepiece (LV-NU5AI).
Attaching DIC prisms (objective and condenser) for epi and diascopic illumination.
Mounting the LV-UEPI2A unit, connecting cables, and installing light shields.
How to insert sliders into the LV-UEPI2A.
How to install filter sliders and filters into the epi illuminator.
Steps for installing filter cubes or PA blocks into the LV-UEPI2A turret.
Procedures for attaching the lamp house and replacing lamps.
Connecting the TE2-PS100W for simultaneous illumination.
Connecting external light sources, adapters, and RS-232C cables.
Installing the compensation filter with the HG fiber adapter.
Attaching the adapter for switching between light sources.
Installing the eyepiece tube, eyepieces, and objectives.
How to attach and adjust polarizers for diascopic illumination.
Attaching optional risers to adjust eyepiece height and column riser.
Connecting the PC for microscope setup using LVSetup software.
Connecting the DS-L2 controller for camera control.
Connecting the power cord and notes on anti-static features.
Troubleshooting for viewfield visibility, brightness, contrast, and resolution.
Solutions for focus problems, image elongation, and specimen drift.
Troubleshooting for color tints, brightness control, and illumination problems.
Diagnosing and resolving electrical issues with power, lamps, and controllers.
Troubleshooting for LV-UEPI2A and motorized nosepiece specific issues.
Detailed technical specifications for the main microscope unit.
Detailed specifications for the LV-UEPI2A epi illuminator.
Detailed specifications for the motorized nosepieces.
Detailed specifications for the TE2-PS100W power supply.
Environmental requirements for operation, storage, and safety compliance.
General| Brand | Nikon |
|---|---|
| Model | Eclipse LV100DA-U |
| Category | Microscope |
| Language | English |
To Next Page