OHAUS Explorer EX1241

To Next Page

To Previous Page

EXPLORER BALANCES EN-149

Figure 9-4. EX12001, EX24001 and EX35001 models

14.8 in.

377 mm

4.7 in.

120 mm

17.4 in.

443 mm

12.1 in.

1.9 in.

48 mm

311 mm

Main Page

Table of Contents3
Introduction7
Description7
Features7
Safety Precautions8
Intended User8
Installation9
Unpacking9
Terminal Setup10
Installing the Wind Ring, Weighing Platform on Semi-Micro Models10
Installing the Wind Ring, Weighing Platform on Models EX12410
Installing the Glass Shelf (on Semi-Micro Models)12
Installing the Weighing Pan & Wind Shield - Non-Draft Shield Models12
Selecting the Location13
Leveling the Equipment13
Connecting Power13
Models with AC Adapter13
Models with AC Power Cord14
Power on Button on EX12001, EX24001 and EX3500114
Connecting the Interface14
Adjusting the View Angle of the Terminal14
Remote Terminal Operation15
Separating the Terminal from the Weighing Base15
Terminal Mounting15
Initial Calibration16
Operation17
Overview of Display, Home Screen17
Principal Functions and Main Menu17
Overview of Parts and Features18
Overview of Parts and Features -Draft Shield Models19
Overview of Parts and Features - Non-Draft Shield Models20
Overview of Parts and Features - EX12001, EX24001 and EX3500121
Overview of Parts and Features - Terminal22
Functions and Their Icons23
Standby23
Printing Data23
Zero Operation23
Touchless Sensor Status23
Autocal23
Menu23
More23
Level Assist23
Graduations24
Routine Test24
Applications24
Taring a Container24
Weighing Units24
Ionizer (Only for EX225D/AD and EX225/AD)24
Preset Tare24
Calibration Test24
Calculator24
Stopwatch25
Logout25
Ionizer (EX225D/AD and EX225/AD Only) and Glass Shelf25
Application26
Weighing27
Edit Settings27
Application Setup29
Statistics for Weighing30
Parts Counting33
Standard Parts Counting (Default)33
Application Setup36
Parts Counting - Check37
Parts Counting - Fill38
Statistics for Parts Counting39
Percent Weighing41
Edit Settings41
Application Setup43
Check Weighing44
Standard Check Weighing (Default)44
Edit Settings44
Application Setup45
Check Weighing - Nominal/Weight Tolerance Mode46
Check Weighing - Nominal/Percent Tolerance Mode47
Display Settings48
Statistics for Check Weighing49
Dynamic/Animal Weighing50
Edit Settings51
Application Setup51
Dynamic Weighing - Semi-Auto52
Dynamic Weighing - Automatic53
Statistics for Dynamic Weighing54
Filling55
Edit Settings55
Application Setup56
Statistics for Filling57
Totalization59
Totalization - Manual (Default)59
Application Setup60
Totalization - Automatic61
Formulation62
Free Formulation (Default)62
Application Setup63
Recipe Formulation64
Differential Weighing67
Item Settings67
Application Setup69
Differential Weighing with Auto-Process on70
Density Determination71
Measuring the Density of a Solid Using Water (Default)71
Application Setup73
Measuring the Density of a Buoyant Material Using Water74
Measuring the Density of a Solid Using an Auxiliary Liquid74
Measuring the Density of a Liquid Using a Calibrated Sinker (Not Supplied)75
Measuring the Density of Porous Material Using Oil77
Peak Hold79
Peak Hold - Semi-Automatic (Default)79
Application Setup80
Peak Hold - Manual81
Peak Hold - Automatic82
Ingredient Costing (Not Available in Semi-Micro Models)83
Item Settings83
Application Setup86
Pipette Adjustment (Not Available in EX12001, EX24001, EX35001)87
Pipette Adjustment - Manual (Default)87
Begin Pipette Adjustment Process89
Application Setup90
Statistical Quality Control (SQC)91
Edit Settings91
Begin the SQC Process92
Application Setup93
Fill Weight Variation95
Edit Settings95
Begin the Fill Weight Variation Process97
Application Setup98
Statistics99
Secondary Unit99
Library100
Creating a Library Record101
Retrieving a Library Record101
Deleting a Stored Library Record101
Additional Features102
Weigh below102
Menu Settings103
Menu Navigation103
Changing Settings103
Main Menu103
Calibration104
Calibration Sub-Menu104
Internal Calibration (Autocal™)104
Automatic Calibration104
Auto TM Interval (Hours)105
Autocal™ Adjustment105
Span Calibration105
User Calibration106
Calibration Test106
User Management107
User Settings109
User Settings Sub-Menu109
Change Password109
Language109
Volume109
Display Settings109
Functions Configuration110
Touchless Sensor Setup110
Draft Shield Light110
Ionizer (Seconds)110
Balance Setup111
Balance Set-Up Sub-Menu111
Stable Range111
Filter Level111
Auto Zero Tracking111
Audible Signal111
Auto Tare112
Gross Indicator112
Legal for Trade112
Graduations112
Internal Calibration112
Date & Time113
Applications114
Turning an Application ON/OFF114
Weighing Units114
Units Sub-Menu114
Turning a Unit ON/OFF115
Custom Units115
GLP and GMP Data116
GLP Data Sub-Menu116
Header116
Balance Name116
Project Name116
Communication116
Communication Sub-Menu116
Device & Print Settings116
Baud Rate117
Transmission117
Handshake117
Alternate Command117
Print Output117
Auto Print118
Print Calibration Data118
Print Content118
Print Layout120
Data Transfer Function121
Label Template122
Save to USB Flash Drive122
Library124
Diagnostics125
Routine Test125
Level Bubble Light (Not Available in EX12001, EX24001, EX35001)125
Draft Shield Light (Analytical Models)125
Sensors125
Automatic Draftshield Door125
Data Maintenance126
Service Mode126
Factory Reset127
Factory Reset Sub-Menu127
Reset Calibration127
Reset User Settings127
Reset Balance Setup127
Reset Application Modes127
Reset Weighing Units127
Reset GLP and GMP Data127
Reset Communication127
Reset All (Global Reset)127
Information128
Using Information128
Legal for Trade129
Settings129
Verification129
Sealing129
Printing130
Connecting, Configuring and Testing the Printer/Computer Interface130
Printout Examples131
Minimum Weight131
Output Format141
Maintenance142
Calibration142
Cleaning142
Battery Power142
Troubleshooting142
Service Information142
Technical Data143
Specifications143
Drawings and Dimensions150
Parts and Accessories152
Communication153
Interface Commands153
RS232 (DB9) Pin Connections156
The USB Interface156
Software Updates159
Compliance160

OHAUS Explorer EX1241 - Page 151

Table of Contents

Related product manuals