- 270 -
9. Operating Management/ Specifications
• Fax Setting
PreFix (NULL) Sets the dialing prefix. You can enter up to 40
digits.
Received Time Stamp OFF Sets whether to print the time stamp on
received faxes.
Print Check Message ON Sets whether to report the error content if a
transmission error occurs.
Duplex OFF or
ON(Duplex)
Sets simplex or duplex for printing received
fax and the binding position for duplex
printing.
Distant Station Priority Type 1 Sets the priority order of information for
Distant Station (information of the
destination).
Priority (High > Low)
[Type 1]: Destination information > Name in
speed dial > Phone number
[Type 2]: Name in speed dial > Phone
number
Item Factory
default
setting
Description
Service Bit OFF If set to OFF, some menu items are not
displayed on the screen.
Country Code International or
U.S.A
Sets the country code.
A/R Full Print ON Sets whether to print the list of the
communication results automatically after
every 50 communications.
Daily Tx/Rx Log Report Setting OFF Enables / disables to print a daily report.
Print Time 0 Hour
0 Minute
0 Second
Sets the date and time for printing the daily
report.
Tone For Echo (For Transmission) Disable Displays only if Service Bit is ON.
Tone For Echo (For Reception) Disable Displays only if Service Bit is ON.
H/Modem Rate (For Tx) 33.6 Kbps Sets the default modem reception
transmission speed while the machine is
sending a fax.
H/Modem Rate (For Rx) 33.6 Kbps Sets the default value of the modem
transmission speed while the machine is
receiving a fax.
Item Factory
default
setting
Description
Attenuator 10 dB, Range:
0 - 15 dB
Enter Attenuator. Displays only if Service Bit
is ON.
MF Attenuator 8 dB, Range: 0
- 15 dB
Enter MF(Tone) Attenuator. Displays only if
Service Bit is ON.
Pulse Make Ratio 40%, Range:
33, 39, 40%
Sets to make rate of DP (10 pps) during call.
Displays only if Service Bit is ON and Tone /
Pulse setting is PULSE.
Pulse Dial Type N, Range: N,
10-N, N+1
Sets the pulse type for dialing. Displays only
if Service Bit is ON and Tone / Pulse setting
is PULSE.
MF(Tone) Duration 100 mseconds,
Range: 75, 85,
100 mseconds
Enter MF(Tone) Duration. Displays only if
Service Bit is ON and Tone / Pulse setting is
TONE.
Calling Timer 60 mseconds,
Range: 1 -
255 seconds
Displays only if Service Bit is ON.
PBX Line OFF When connecting to PBX (internal
exchange), put it to [ON].
Forwarding
Setting
Forwarding Setting OFF Sets whether to enable the fax forwarding
mode.
Forwarding Number (NULL) Sets a fax number used for the fax
forwarding mode.
TAD Mode Type 3 Sets an operation type in Tel / Fax Ready
mode.
[Type 3]: A fax signal is detected in
15 seconds from when the answering
machine answers. Normally, use this type.
[Type 1]: A fax signal is detected right after
the answering machine answers, and then
the reception starts. If you have any fax
reception problems, they may be improved if
this type is set.
[Type 2]: A fax signal is detected right after
the answering machine answers. Set this
type if you usually use this machine as a
phone.
Tel Priority Mode OFF Sets when the external telephone and the
machine ring in Tel / Fax Ready mode.
[ON]: The sender is assumed to make a
voice call. The telephone rings early.
CNG Detection OFF Sets whether to determine whether the
sender is sending a fax during the off the
hook condition in Tel / Fax Ready mode.
Item Factory
default
setting
Description
To Next Page
Loading...
Need help?
General
