Omron 3G3MX2 - Page 116

SYSDRIVE MX2 Series USER'S MANUAL (3G3MX2-A@@@@)
5
Functions
Input Terminal Response Time ..................................................... 5-32
Multi-function Output Terminal Selection ...................................... 5-32
Multi-function Output Terminal Contact Selection......................... 5-34
Output Signal Delay/Hold Function ............................................... 5-36
5-4 Analog Signal...................................................................... 5-37
Analog Input (FV, FI)..................................................................... 5-37
Analog Input Filter (FV, FI Sampling)............................................ 5-38
Analog Command Held Function (AHD) ....................................... 5-39
Analog Input Adjustment............................................................... 5-40
External Frequency Start/End....................................................... 5-40
MP Terminal (Pulse/PWM Output)................................................ 5-42
AM Terminal (Analog Output) ....................................................... 5-44
5-5 Settings Relating to Control Method ................................ 5-46
Control Method (V/f Characteristics)............................................. 5-46
Torque Boost ................................................................................ 5-49
Carrier Frequency ......................................................................... 5-51
Automatic Carrier Frequency Reduction Function ........................ 5-52
Motor 2 Control Function (SET) .................................................... 5-54
5-6 Operation Functions .......................................................... 5-56
3-wire Input Function (STA, STP, F/R) ......................................... 5-56
Starting Frequency........................................................................ 5-57
Reduced Voltage Startup Selection .............................................. 5-58
Jogging Operation (JG)................................................................. 5-59
Frequency Limit ............................................................................ 5-60
Frequency Jump Function ............................................................ 5-61
Acceleration/Deceleration Stop Function ...................................... 5-62
RUN Permission Signal ................................................................ 5-63
Multi-step Speed Operation Function (CF1 to CF4, SF1 to SF7) .....5-63
2-step Acceleration/Deceleration Function (2CH)......................... 5-66
Acceleration/Deceleration Pattern ................................................ 5-68
Frequency Operation Function ..................................................... 5-70
Frequency Addition Function ........................................................ 5-71
Remote Operation Function (UP, DWN) ....................................... 5-71
Output Voltage Gain ..................................................................... 5-72
PID Function ................................................................................. 5-73
Automatic Energy-saving Operation Function .............................. 5-79
Commercial Switch (CS) ............................................................... 5-79
Stabilization Parameter................................................................. 5-81
Pulse Train Frequency Input......................................................... 5-82
V/f Control with Speed Feedback ................................................. 5-83
5-7 Digital Operator/Operation Functions .............................. 5-84
STOP Key Selection ..................................................................... 5-84
Soft Lock Function (SFT) .............................................................. 5-84
Forced Operator Function (OPE) .................................................. 5-85
Forced Terminal Block Function (F-TM) ....................................... 5-85
Selection of Operation upon Digital Operator Disconnection........ 5-86
Initial Screen Selection (Screen at Power-ON) ............................. 5-86
Initial Screen Automatic Switching Function ................................. 5-87
Main Panel Display Selection ....................................................... 5-87
Display Selection .......................................................................... 5-88
Display Fixed (DISP)..................................................................... 5-91
Password Function ....................................................................... 5-91
5-8 Restart Functions............................................................... 5-94
Frequency Matching Restart and Frequency Pull-in Restart ........ 5-94
Restart Upon Momentary Power Interruption/Undervoltage, Overvoltage/Overcurrent .... 5-96
Reset (RS) .................................................................................. 5-100
Free-run Stop Function (FRS) .................................................... 5-103
Power Recovery Restart Prevention Function (USP) ................. 5-105
Deceleration Stop at Power-off (Controlled Deceleration on Power Loss Function) ... 5-106
5-9 Functions Relating to Protections, Warnings and Various Output Signals ..... 5-110
Electronic Thermal Function ....................................................... 5-110
Overload Limit/Overload Warning............................................... 5-114