Omron 3G3MX2 - Page 436

INDEX-4
INDEX
I
Overcurrent suppression function ............... 5-116
Overload limit
.................................................... 5-114
Overload warning
............................................ 5-115
Overtorque
........................................................ 5-152
Overvoltage suppression function during
deceleration
...................................................... 5-117
Overvoltage/overcurrent restart
..................... 5-96
P
P24 .......................................................................... 2-8
Password function
............................................. 5-91
PID feedback value monitor
.............................. 5-2
PID function
........................................................ 5-73
PIDC
..................................................................... 5-78
Position command monitor
............................... 5-9
Power ON time
..................................................... 5-8
Power ON time over
....................................... 5-124
Power recovery restart prevention
function
............................................................... 5-105
PSC
......................................................................... 2-8
Pulse train frequency input
............................. 5-82
R
Real frequency monitor...................................... 5-5
Reduced torque characteristics
........ 5-47, 5-111
Reduced voltage startup selection
................ 5-58
REF
..................................................................... 5-133
Regenerative braking function
..................... 5-141
Regenerative braking load rate monitor
...... 5-12
Remote operation function
.............................. 5-71
Reset
.................................................................. 5-100
Reverse rotation prevention function
.......... 5-157
RNT
..................................................................... 5-124
Rotation direction limit selection
.................... 5-23
Rotation direction monitor
................................. 5-2
RP
............................................................................ 2-9
RS
........................................................................ 5-100
RUN
.................................................................... 5-121
RUN command selection
................................. 5-22
RUN command source
................................... 5-133
RUN direction selection
................................... 5-23
RUN permission signal
.................................... 5-63
RUN time over
.................................................. 5-124
RV
.......................................................................... 5-22
RVR
..................................................................... 5-131
S
Safety function.................................................. 5-170
Safety function selector switch
............. 2-5, 5-170
SC
............................................................................ 2-7
Selection of operation on digital operator
disconnection
...................................................... 5-86
Sensorless vector control
.............................. 5-144
SET
....................................................................... 5-54
SETM
.................................................................. 5-134
SF1 to SF7
.......................................................... 5-63
SFT
........................................................................ 5-84
Signal during forward operation
................... 5-130
Signal during reverse operation
................... 5-131
Signal during RUN
........................................... 5-121
Simple position control mode
....................... 5-160
Sink logic
............................................................. 2-19
Soft lock function
............................................... 5-84
Source logic
........................................................ 2-19
Speed/position switching function
............... 5-167
STA
....................................................................... 5-56
Stabilization parameter
.................................... 5-81
Start frequency
................................................... 5-40
Start ratio
............................................................. 5-40
Start selection
..................................................... 5-40
User selection
..................................................... 5-88
Starting contact signal
.................................... 5-128
Starting frequency
............................................. 5-57
STOP key selection
.......................................... 5-84
Stop selection
..................................................... 5-24
STP
....................................................................... 5-56
T
Test Run .............................................................. 3-10
TH
................................................................ 2-8, 5-120
Thermal warning
.............................................. 5-113
Thermistor trip function
.................................. 5-120
Torque bias function
....................................... 5-156
Torque bias monitor
............................................ 5-6
Torque boost
....................................................... 5-49
Torque control
.................................................. 5-156
Torque LADSTOP function
........................... 5-155
Torque limit function
....................................... 5-153
Torque monitor function
................................. 5-151
Torque reference monitor
.................................. 5-5
Total RUN time
..................................................... 5-8
Trip
................................................................ 3-12, 7-1
TRQ
..................................................................... 5-154
U
UDC ...................................................................... 5-71
Undertorque
...................................................... 5-152
UP
.......................................................................... 5-71
User parameter automatic setting
function
............................................................... 5-177
User parameter manual setting function
... 5-177
User selection monitor
..................................... 5-10
USP
..................................................................... 5-105
UV
.......................................................................... 5-97