Omron E5CC-800 User Manual

A Appendices
A - 24
Digital Temperature Controllers (Simple Type) User’s Manual (H211)
A-8 Parameter Flow
This section describes the parameters set in each level. Pressing the M Key at the last parameter in
each level returns to the top parameter in that level.
M
M
M
M
M
M
M
Press the O Key
less than 1 s.
Communications
Setting Level
Displayed only for models with communications.
Changes are effective after cycling power or after
a software reset.
Protocol Setting:
Switches between
CompoWay/F and
Modbus.
Communications Unit No.
Communications
Baud Rate
CompoWay/F
only
Communications
Data Length
Communications
Stop Bits
Communications Parity
Send Data Wait Time
psel
cwf
u-no
1
bps
9.6
len
7
sbit
2
prty
even
sdwt
20
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
Proportional
Band
(Cooling)
M
SP 4
M
SP 5
M
SP 6
M
SP 7
Integral
Time
(Cooling)
Derivative
Time
(Cooling)
M
Process Value Input
Shift
Process Value/
Set Point 1
Process Value/
Set Point 2
*1
*1
Starting in manual mode.
ST (Self-tuning)
Power ON
Starting in
automatic
mode.
Manual Control Level
PID
Control
only
PV/MV
Press the O Key less than 1 s.
Press the O Key less than 1 s.
Operation Level
Adjustment
Level
AT Execute/Cancel
SP 0
SP 1
SP 2
SP 3
Proportional
Band
Integral
Time
PID
settings
Derivative
Time
Dead Band
Manual Reset Value
Clear the offset during
stabilization of P or
PD control.
Hysteresis (Heating)
Hysteresis (Cooling)
Hysteresis settings
SP Ramp Set Value
MV Upper Limit
MV Lower Limit
Auto/Manual Switch
PID control only.
Added when auto/manual
select addition is ON.
Multi-SP Set Point
Selection
Set Point During
SP Ramp
Press the O and M
Keys for at least 3 s.
Protect Level
Press the O and M Keys for at
least 1 s.
The time taken to move to the protect level can be adjusted
by changing the "Move to protect level time" setting.
Operation/Adjustment Protect:
Restricts displaying and modifying
menus in operation, adjustment, and
manual control levels.
Initial Setting/Communications Protect:
This protect level restricts movement to
the initial setting, communications setting,
and advanced function setting levels.
Setting Change Protect:
Protects changes to setups by
operating the front panel keys.
PF Key Protect
RUN/STOP
Alarm Value 1
Set either of these parameters.
Alarm Value Upper
Limit 1
Alarm Value Lower
Limit 1
Alarm Value 2
Set either of these parameters.
Alarm Value Upper
Limit 2
Alarm Value Lower
Limit 2
Alarm
Value 3
Alarm Value
Upper Limit 3
Alarm Value
Lower Limit 3
Set either of these parameters.
MV Monitor
(Heating)
MV Monitor
(Cooling)
Press the
O Key for
at least 1 s.
Press the O Key for less than 1 s.
Initial Setting Level
Input Type
Scaling Upper Limit
Scaling Lower Limit
Decimal Point
For input type of analog
Temperature Unit
°C, °F
For input type
of temperature
SP Upper Limit
SP Lower Limit
Limit the set point
PID ON/OFF
Standard or
Heating/Cooling
For input type of
temperature, standard
control, or PID
Control Period (Heating)
Control Period (Cooling)
Set the ON/OFF
output cycle.
Direct/Reverse Operation
Alarm 1 Type
Alarm 1
Hysteresis
Press the
O Key for at least 3 s.
Other than the Auto/Manual Switch display
Press the S Key
for at least 1 s.
Press the O
Key or the
S
Key for at least
1 s.
*1. When the PF Setting
parameter is set to A-M.
Press the O
Key for at
least 3 s.
Set either of these parameters.
Alarm Value
Upper Limit 4
Alarm Value
Lower Limit 4
Alarm
Value 4
M
25
0
C
25
0
ins
0.0
c-p
8.0
c-i
233
c-d
40
M
M
M
p
8.0
i
233
d
40
c-db
0.0
of-r
50.0
hys
1.0
chys
1.0
oapt
0
icpt
1
wtpt
off
pfpt
off
Changed Parameters Only
M
chgp
off
M
sprt
off
ol-h
100.0
ol-l
0.0
at
off
sp-0
0
sp-1
0
sp-2
0
sp-3
0
sp-4
0
sp-5
0
sp-6
0
sp-7
0
M
sp-3
0
r-s
run
in-t
5
in-h
100
in-l
0
dp
0
d-u
c
sl-h
1300
sl-l
-200
cntl
onof
s-hc
stnd
st
on
cp
20
c-cp
20
orev
or-r
alt1
2
alh1
0.2
al-1
0
al1h
0
al1l
0
al-2
0
al2h
0
al2l
0
al-4
0
al4h
0
al4l
0
M
M
M
al-3
0
al3h
0
al3l
0
o
0.0
c-o
0.0
25
0
a-m
m-sp
0
sp-m
0
M
M
M
Communications
Writing
Heater Current 1
Value Monitor
Heater Burnout
Detection 1
Leakage Current 1
Monitor
HS Alarm 1
cmwt
off
ct1
0.0
M
hb1
0.0
lcr1
0
hs1
50.0
M
Heater Current 1 Value
Monitor
Leakage Current
1 Monitor
ct-1
0.0
lcr1
0.0
M

Omron E5CC-800 Specifications

General

Communication	RS-485 (optional)
Protection Rating	IP66 (front panel)
Input Type	Thermocouple, RTD, analog input
Output Type	Relay, voltage, current
Supply Voltage	100-240 VAC, 24 VAC/VDC
Size	48 x 48 mm
Control Output	Relay, voltage, current
Ambient Operating Temperature	55 °C
Control Method	ON/OFF, 2-PID
Ambient Operating Humidity	35 to 85% RH (non-condensing)
Mounting	Panel mount