Omron J1000 User Manual

H4 Multi-Function Analog Output AM................................... 177
H5-01.......................................................................... 177
H5-02.......................................................................... 177
H5-03.......................................................................... 177
H5-04.................................................................... 124, 177
H5-05.......................................................................... 177
H5-06.......................................................................... 177
H5-07.......................................................................... 177
H5-12.......................................................................... 177
H5-13.......................................................................... 177
H5 MEMOBUS/Modbus Communications .............................. 177
Heatsink Cooling Fan Operation Selection............................... 179
Heatsink Overheat ............................................... 121, 122, 130
Heavy Duty Ratings ......................................................... 162
Hunting Prevention Gain ................................................... 120
Hunting Prevention Gain Setting .......................................... 180
I
I/O Connections................................................................32
IGBT Maintenance .......................................................... 182
IGBT Maintenance Setting ................................................. 181
Initialize Parameters......................................................... 171
Initial Operation................................................................62
Input Current (A) ...................................................... 163, 164
Input Fuses.................................................................... 212
Input Phase Loss ....................................................... 121, 127
Input Terminals ................................................................60
Input Voltage Setting........................................................ 174
Inrush Prevention Circuit Fault ............................................ 127
Inrush Prevention Relay Maintenance Setting........................... 181
Inspection ............................................................... 142, 143
Installation Environment......................................................26
Installation Orientation........................................................27
Installation Spacing............................................................27
Installing Multiple Drives ....................................................27
Internal Dynamic Braking Resistor Protection ............................47
Internal Dynamic Braking Resistor Protection Selection (ERF type)
.................................................................................. 179
J
Jog Frequency Reference ................................................... 173
Jog Reference Selection..................................................... 175
Jump Frequency.............................................................. 120
Jump Frequency 1 ........................................................... 174
Jump Frequency 2 ........................................................... 174
Jump Frequency Width ..................................................... 174
L
L1-01 .............................................................. 125, 177, 219
L1-02 .................................................................... 178, 219
L1-13 .......................................................................... 178
L1 Motor Protection Functions ............................................ 177
L2-01 .......................................................................... 178
L2 Momentary Power Loss................................................. 178
L3-01 .......................................................................... 178
L3-01 through L3-06 ........................................................ 120
L3-02 .............................................................. 136, 137, 178
L3-04 ..........................................................47, 126, 136, 178
L3-05 .......................................................................... 178
L3-06 .................................................................... 136, 178
L3 Stall Prevention Function............................................... 178
L4-01 .......................................................................... 178
L4 Frequency Detection .................................................... 178
L5-01 .................................................................... 130, 178
L5 Fault Reset................................................................ 178
L6-01 .......................................................................... 179
L6-02 .............................................................. 126, 130, 179
L6-03 .............................................................. 126, 130, 179
L6 Overtorque Detection ................................................... 179
L8: Hardware Protection.................................................... 179
L8-01 ................................................................47, 127, 179
L8-05 .......................................................................... 127
L8-10 .......................................................................... 179
L8-12 .................................................................... 168, 179
L8-18 .......................................................................... 179
L8-29 .......................................................................... 168
L8-38 .................................................................... 137, 179
LED Check ................................................................... 182
LED Operator .........................................................19, 54, 55
LO/RE..................................................................55, 60, 64
LOCAL..........................................................................60
Local/Remote Run Selection............................................... 171
Local/Remote Selection..................................................... 175
Low Voltage Directive...................................................... 212
L Protection Function ....................................................... 177
M
Magnetic Flux Compensation Capacity .................................. 172
Main Circuit Connection Diagram ..................................... 34, 39
Main Circuit Terminal Functions............................................37
Main Circuit Terminal Power Supply.......................................38
Main Circuit Terminals Connection.........................................34
Main Circuit Terminal Wiring .........................................21, 218
Main Frequency Reference ...................................................46
Main Frequency Reference Input............................................41
Maintenance .................................................................. 144
Master Speed Reference Lower Limit .................................... 173
Maximum Motor Size Allowed (kW)............................... 163, 164
Max Output Frequency...................................................... 174
MEMOBUS/Modbus Communication Error........... 121, 122, 123, 129
MEMOBUS/Modbus Communications Test Mode Complete ........ 130
MEMOBUS/Modbus Communications Test Mode Error.............. 131
MEMOBUS/Modbus Error Code ......................................... 182
MEMOBUS/Modbus Test Mode Complete.............................. 122
Mid Output Voltage A ...................................................... 120
Minimum Output Frequency ......................................... 137, 138
Minimum Output Voltage .................................................. 120
Minor Alarms ................................................................ 121
Minor Faults .................................................................. 121
Modes ...........................................................................57
Momentary Power Loss Operation Selection ............................ 178
Monitor Output.................................................................41
Motor Does Not Operate When an External Run Command is Input
.................................................................................. 138
Motor
Does Not Operate When the RUN Button on the Digital Operator
is Pressed...................................................................... 137
Motor Does Not Rotate ..................................................... 134
Motor Hunting and Oscillation Control Parameters .................... 120
Motor Hunting Occurs When Operating With a Light Load........... 136
Motor is Too Hot ............................................................ 135
Motor Line-to-Line Resistance ............................................ 174
Motor No-Load Current..................................................... 174
Motor Overload ........................................................ 121, 125
Motor Overload Protection Selection ............................... 177, 219
Motor Overload Protection Time .................................... 178, 219
Motor Protection Function.................................................. 125
Motor Rated Current .................................................. 174, 219
Index
SIEP C710606 33A OYMC AC Drive – J1000 User Manual
225

Omron J1000 Specifications

General

Brand	Omron
Model	J1000
Category	Inverter
Language	English