Panasonic PT-FRQ50

Chapter 3 Basic Operations — Switching on/o󰀨 the projector
ENGLISH - 41
Indicator status Projector status
O󰀨 The main power is switched o󰀨.
Red
Lit
The power is switched o󰀨. (standby mode)
Projection will start when the power <
v
/
b
> button is pressed.
f
The setting of the projector is as follows.
g
The [PROJECTOR SETUP] menu
→
[ECO MANAGEMENT]
→
[QUICK STARTUP] is set to [OFF]
g
The [PROJECTOR SETUP] menu
→
[AUDIO SETTING]
→
[IN STANDBY MODE] is set to [OFF]
f
The projector may not operate when the light source indicator <LIGHT> or the temperature indicator
<TEMP> is blinking. (
x
page 192)
Blinking
The power is switched o󰀨. (standby mode)
Projection will start when the power <
v
/
b
> button is pressed.
f
The projector is in one of the following states.
g
The [PROJECTOR SETUP] menu
→
[ECO MANAGEMENT]
→
[QUICK STARTUP] is set to [ON]
g
The [PROJECTOR SETUP] menu
→
[AUDIO SETTING]
→
[IN STANDBY MODE] is set to [ON]
g
The output image corresponding to the projected image from the projector is being checked by
the web control function. For details, refer to “[Remote preview lite] page” (
x
page 156).
f
The indicator will change to a red light when the specied time has elapsed after the projector enters
the standby mode if the projector is set as following. However, the indicator will not change to a red
light while the output image is being checked by the web control function.
The specied time is a time set in the [PROJECTOR SETUP] menu
→
[ECO MANAGEMENT]
→
[QUICK STARTUP]
→
[VALID PERIOD].
g
The [PROJECTOR SETUP] menu
→
[ECO MANAGEMENT]
→
[QUICK STARTUP] is set to [ON]
g
The [PROJECTOR SETUP] menu
→
[AUDIO SETTING]
→
[IN STANDBY MODE] is set to [OFF]
f
The projector may not operate when the light source indicator <LIGHT> or the temperature indicator
<TEMP> is blinking. (
x
page 192)
Green Lit Projecting.
Orange Lit
The projector is preparing to switch o󰀨 the projector.
The power is switched o󰀨 after a while. (Changes to the standby mode.)
Note
f
While the power indicator <ON (G)/STANDBY (R)> lights orange, the fan is running to cool the projector.
f
For approximately ve seconds after the projector is turned o󰀨, the indicator does not light up even if the power is turned on. Turn on the
power again after the power indicator <ON (G)/STANDBY (R)> lights/blinks red.
f
The projector consumes power even in standby mode (power indicator <ON (G)/STANDBY (R)> lights/blinks red). Refer to “Maximum power
consumption” (
x
page 210) for the power consumption.
f
The power indicator <ON (G)/STANDBY (R)> will blink if the projector receives a remote control signal.
f
The power indicator <ON (G)/STANDBY (R)> will blink green slowly while the shutter function is in use (shutter: closed), or while the function
of the [PROJECTOR SETUP] menu
→
[ECO MANAGEMENT]
→
[POWER MANAGEMENT]
→
[NO SIGNAL LIGHTS-OUT] is operating
and the light source is turned o󰀨.
Switching on the projector
2)
4)
4)
3)
1)
1) Connect the power cord to the projector.
2) Connect the power plug to an outlet.
3) Press the <ON> side of the <MAIN POWER> switch to turn on the power.
f
The power indicator <ON (G)/STANDBY (R)> lights/blinks red, and the projector enters the standby mode.