Panasonic PT-RS30K - Page 58

INF-48
SECTION 1 SERVICE INFORMATION
<RZ31K/RS30K>
Bit Error code (hex)
Self-test indica-
tion
Details Probable cause
199 00000000 00000080 FC0 Power CPU communication error Communication error on Power CPU
200 00000000 00000100 F97 GEOMETRY communication error Communication error on Geometry IC
201 00000000 00000200 FC2 FRC error Program transferring error to FRC
202 00000000 00000400 F81 FM-R TEST Fail
Abnormal on FM startup mode
Error on FM memory test
203 00000000 00000800 F82 FM-G TEST Fail
204 00000000 00001000 F83 FM-B TEST Fail
205 00000000 00002000 F65 LD1-B Sub CPU error
Divice operation error on DR-PCB
206 00000000 00004000 F66 LD1-S Sub CPU error
207 00000000 00008000 F67 LD2-B Sub CPU error
208 00000000 00010000 F68 LD2-S Sub CPU error
209 00000000 00020000
－
Not used
210 00000000 00040000
－
Not used
211 00000000 00080000
－
Not used
212 00000000 00100000
－
Not used
213 00000000 00200000
－
Not used
214 00000000 00400000
－
Not used
215 00000000 00800000
－
Not used
216 00000000 01000000
－
Not used
217 00000000 02000000
－
Not used
218 00000000 04000000
－
Not used
219 00000000 08000000
－
Not used
220 00000000 10000000
－
Not used
221 00000000 20000000
－
Not used
222 00000000 40000000
－
Not used
223 00000000 80000000
－
Not used
224 00000001 00000000 A41 IIC communication error 1 (RTC)
Divice operation error on Signal PCB
225 00000002 00000000 A42 IIC communication error 2 (EEPROM)
226 00000004 00000000 A47 IIC communication error 7 (EDID DIGITAL)
227 00000008 00000000 A48 IIC communication error 7 (EDID ANALOG)
228 00000010 00000000 A49
IIC communication error 9 (ADC1)
229 00000020 00000000 A50 IIC communication error 10 (ADC2)
230 00000040 00000000 A51 IIC communication error 11 (ACCELERATION SENSOR)
231 00000080 00000000 A52 IIC communication error 12 (OPTICAL SENSOR)
232 00000100 00000000 A53 IIC communication error 13 (HD BaseT)
233 00000200 00000000 A54 IIC communication error 14 (ATM SENSOR)
234 00000400 00000000 A08 Sub CPU communication error (R8) Communication error on Sub CPU
235 00000800 00000000 A97 FM communication error Communication error on FM
236 00001000 00000000
－
Not used
237 00002000 00000000
－
Not used
238 00004000 00000000
－
Not used
239 00008000 00000000
－
Not used
240 00010000 00000000
－
Not used
241 00020000 00000000
－
Not used
242 00040000 00000000
－
Not used
243 00080000 00000000
－
Not used
244 00100000 00000000
－
Not used
245 00200000 00000000
－
Not used
246 00400000 00000000
－
Not used
247 00800000 00000000
－
Not used
248 01000000 00000000
－
Not used
249 02000000 00000000
－
Not used
250 04000000 00000000
－
Not used
251 08000000 00000000
－
Not used
252 10000000 00000000
－
Not used
253 20000000 00000000
－
Not used
254 40000000 00000000
－
Not used
255 80000000 00000000
－
Not used
l How to read the returned value and the self-diagnosis serial control command.
Use the command "QVX:ERRS1" to get the information of Self-diagnosis for this model.
The returned value provides the 255bit self-diagnosis information as follows.
(Table below shows no error occurs)
bit
255 • • • • 200 • • • • 150 • • • • 100 • • • • 50 • • • • 1 0
ERRS1= N • • • • N • • • • N • • • • N • • • • N • • • • N N
The returned value "N" indicates normal and "E" indicates error status. The first bit 0 starts from right and it ends by 255th bit
at left.
Example: If the self-diagnosis information is inquired under the condition of the projection lens un-mounted, the "E" will ap-
pear on 70th bit as the below.
bit
255 • • • • 200 • • • • 150 • • • • 100 • 70 • • 50 • • • • 1 0
ERRS1= N • • • • N • • • • N • • • • N • E • • N • • • • N N
"E" will appear on 70th bit.