Item Operational
Condition and Key
Fun
ction
Details Display TO Exit Mode
Jitter display While the player is
stopped and no disc
is inserted, press
and hold down the
button on the
player and the
nu
mber button, “5”
on
theremote
controller unit.
Jitter display
Measures and displays jitter. Measurement is
repeated every second. Read error counter
starts at 0 at the mode setting, and increased
by one as data read fails at target block. A
small defectis allowed to correct by retry.
An
y possibility is counted as one increment.
Repetitive errors after retry increase by two
levels or more.
J*1 xxx*2 _yyy*3 _zz*4
*1
: Jitter display mode
*2
: Jitter measurement value
*3
: Readerror counter
*4 : Focus driving value
Values are shown to one decimal
place in the decimal digit.Focus
dr
iving value is displayed in the
hexadecimal digit.
Press the STOP
or O
PEN button.
Error code display While the player is
stopped and no disc
is inserted, press
and hold down the
button on the
player and the
Error code display
Display
s the latest error code stored in
EE
PROM.
DVDnn_
F---
*nn: Error history
*-
-: Error number
DVD
01 FOBF
Press the OPEN
bu
tton.
15.6 Mode Table 2
Following modes are available with combinations of the pressed buttons on the player and on the remote controller unit.
number button, “0”
on theremote
controller unit.
Measurement of
laser current
electricity
ini
tialization value
Whil
e the player is
stopped and no disc
is inserted, press
and hold down the
button on the
player and the
button on the
remote controller
un
it.
Measurement of laser current electricity
ini
tialization value
Me
morizes each initialization value of DVD
and CD in EEPROM.
LDO*1 _013*2 _032*3
*1
: Laser current electricity
measurement mode
*2
: DVD current electricity value
*3
: CDcurrent electricity value
Values are shown in the decimal
digit. The above example indicates
that the current electricity
initialization value is 13mA at
DVD la
ser and 32mA at CD laser
when laser is turned on.
Auto
matically
exits the mode
after five
seconds.
Measurement of
DVD lase
r current
electricity
Whil
e the player is
stopped and no disc
is inserted, press
and hold down the
button on the
player and the
DISPLAY button on
th
e remote
controller unit.
Meas
urement of DVD laser current electricity
Measures DVD laser current electricity and
di
splays the result together with the
initialization value stored in EEPROM. After
measurement, DVD laser is lit tillthe power is
tu
rned off (or goes off when the primary
po
wer is turned off).
LDD*1 _012*2 _014*3
*1
: DVD laser current electricity
measurement mode
*2
: Current electricity
ini
tializationvalue stored in
EE
PROM
*3 : Present value of current
electricity
Values are shown in the decimal
di
git. The above example indicates
that the current electricity
initialization value is 12mA and
its
present value is 14mA.
Auto
matically
exits the mode
after five
seconds.
ADSC internal
RAM display
While the player is
stopped and no disc
is inserted, press
and hold down the
button on the
player and the
nu
mber button “1”
or
“2” onthe remote
controller unit.
ADS
C internal RAM display
Reads and displays the RAM value inside
AD
SC. The address is renewed when the
CLE
AR key is pressed so that the values at
eleven points appear.
A*1 _FB0*2 _0000*3
*1
:ADSC internal RAM display
mode
*2
: Address
*3 : RAM value atdisplayed
address
Va
lues are shown in the
hexadecimal digit. The above
example indicates that ADSC value
at the address, FB0h is 0000h.
Pr
ess the STOP
or OPEN button.
To Next Page
Loading...
