Table of Contents
Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany
Pepperl+Fuchs Group · Tel.: Germany (6 21) 7 76-0 · USA (3 30) 4 25 35 55 · Singapore 7 79 90 91 · Internet http://www.pepperl-fuchs.com
issue date 21.12.05
3
8.2.4.1 Overview of the Commands .............................................................................. 60
8.2.4.2 Set Operation Mode (SET_OP_MODE: Set_Operation_Mode) ........................ 60
8.2.4.3 Store Actual Configuration (STORE_CDI) ......................................................... 61
8.2.4.4 Read Actual Configuration (READ_CDI) ........................................................... 61
8.2.4.5 Set Permanent Configuration (SET_PCD) ........................................................ 62
8.2.4.6 Get Extended Permanent Configuration (GET_PCD) ....................................... 63
8.2.4.7 Set List of Projected Slaves (SET_LPS and SET_LPS_R6 (6Bh)) ................... 63
8.2.4.8 Get List of Projected Slaves (GET_LPS) ........................................................... 64
8.2.4.9 Store Actual Parameters (STORE_PI) .............................................................. 64
8.2.4.10 Write Parameter (WRITE_P) ............................................................................. 64
8.2.4.11 Read Parameter (READ_PI: Read_Parameter) ................................................ 65
8.2.4.12 Set_Permanent_Parameter (SET_PP) .............................................................. 65
8.2.4.13 Get_Permanent_Parameter (GET_PP) ............................................................. 66
8.2.4.14 Set Auto Address Enable (SET_AAE) ............................................................... 66
8.2.5 Other Commands .............................................................................................. 67
8.2.5.1 Overview of the Commands .............................................................................. 67
8.2.5.2 IDLE ................................................................................................................... 67
8.2.5.3 Read Input Data Image (READ_IDI) ................................................................. 68
8.2.5.4 Write Output Data Image (WRITE_ODI) ........................................................... 68
8.2.5.5 Read Output Data Image (READ_ODI) ............................................................. 69
8.2.5.6 Change Slave Address (SLAVE_ADDR) ........................................................... 69
8.2.5.7 Write AS-i Slave Extended ID1 (WRITE_XID1) ................................................. 70
8.2.5.8 Set Offline Mode (SET_OFFLINE) .................................................................... 70
8.2.5.9 Release Data Exchange (SET_DATA_EX) ....................................................... 71
8.2.5.10 BUTTONS ......................................................................................................... 71
8.2.5.11 FP_PARAM ....................................................................................................... 72
8.2.5.12 FP_DATA .......................................................................................................... 72
8.2.5.13 EXT_DIAG ......................................................................................................... 73
8.2.5.14 RD_EXT_DIAG .................................................................................................. 73
8.2.5.15 INVERTER ........................................................................................................ 74
8.2.5.16 Write Flag .......................................................................................................... 75
8.2.5.17 Read Flag .......................................................................................................... 75
8.2.5.18 READ_MFK_PARAM ........................................................................................ 76
8.3 Command Interface Examples ....................................................................... 76
8.3.1 Reading 16-Bit Input Values .............................................................................. 76
8.3.2 Store current Configuration to the AS-i Master .................................................. 78
8.3.3 Store new Configuration for all Slaves .............................................................. 82
9 Commissioning Tools and Accessories .........................................90
9.1 Windows Software AS-i Control Tools .......................................................... 90
9.2 Further Information ......................................................................................... 93
10 Appendix ............................................................................................94
10.1 Codes indicated by the Display ..................................................................... 94
10.2 Codes indicated by basic master ................................................................... 95
To Next Page
Loading...
