Plockmatic BLM 35

To Next Page

To Previous Page

Rotate Crease Trim Module, continued

1 Creaser tools

2 Jam clearance bafe, ne registra-

tion, section “C”

3 Jam clearance bafe, coarse regis-

tration, section “B”

4 Rotator

Main Page

Default Chapter7
- Table of Contents7
What You Can Do with this Machine11
Guide to Components13
- Booklet Maker13
- User Interface16
  - Control Panel16
Options19
- Rotate Crease Trim Module19
- Booklet Maker24
  - Alive Logo24
  - Cover Feeder25
- Bookfold Module26
- Trimmer28
- BST4000-1 Belt Stacker Module30
  - BST4000-1 Principle of Operation31
1 Basics33
Turning on / off the Main Power33
- RCT, Booklet Maker, Bookfold Module, Trimmer & BST Module33
Change Staple Cartridges and Check Stapler34
- Change Left/Right Staple Cartridge(S)34
- Check Left/Right Stapler35
Cover Feeder35
- Loading Covers35
Emptying the Trim Waste bin36
Belt Stacker37
- Setting up Belt Stacker for Right-Angled Mode37
- Setting up Belt Stacker for Straight Mode38
2 Making Booklets39
Guided Start39
- Guided Start, Step by Step39
Changing Settings42
- General Procedure42
Basic Settings42
- Input Sheet Size42
- Finished Booklet Size43
  - Auto Trimming43
  - Custom Booklet Size44
Customizing Settings45
- Staple45
  - Selecting Stapling on or off45
  - Adjusting Staple Position45
- Fold Position46
  - Adjusting Fold Position46
- Cover46
- Bookfold48
  - General48
  - Selecting Bookfold Pressure Setting49
- Crease50
  - Crease Mode50
  - Crease Position50
Fine-Tuning Booklet Appearance51
- Set Registration (Fine Adjustment)51
- Bleed Trimmer - Asymmetric Side Trim52
- Bleed Trimmer - Cover Adjust52
Hand-Feeding53
- Hand Feed Mode53
3 Tools55
- The Tools Screen55
- Stacker Full Detection55
- Units55
- Software Version56
- Paper Path Light56
- Language56
- Service Mode57
- Fold Delay57
- Sheet Feeder57
- Auto Rotate58
- Bookfold Offset58
4 Jobs59
Handling Jobs59
- Saving a Job59
- Opening and Handling Stored Jobs60
5 Clearing Misfeed(S)61
- General61
RCT Module62
- Clearing Misfeed(S)62
- Infeed "A" Area and Exit "D" Area62
  - Registration and Creaser Area63
Booklet Maker64
- Clearing Misfeed(S)64
Cover Feeder67
- Clearing Misfeed(S) in Vertical Transport Area67
Bookfold Module68
- Clearing Misfeed(S)68
  - Inside the Bookfold Module68
Trimmer69
- Clearing Misfeed(S)69
  - Clearing Misfeed in Input Area69
  - Clearing Misfeed in Exit Area70
Belt Stacker71
- Clearing Misfeed(S)71
  - Clearing Misfeed on Belt Stacker71
6 Troubleshooting73
Fault Codes73
- General73
- RCT Fault Codes73
- Booklet Maker Fault Codes74
- Cover Feeder Fault Codes75
- Bookfold Module Fault Codes76
- Trimmer Fault Codes77
- Belt Stacker Fault Codes77
- General Fault Codes78
7 Remarks79
Do's and Don'ts79
Where to Put Your Machine80
- Machine Environment80
- Power Connection80
- Access to Machine81
Maintaining Your Machines82
- Cover Feeder82
  - Cleaning Feed Rollers and Paper Separator Pad82
- Bookfold Module83
  - Cleaning Feed Belts83
  - Pressure Springs84
- RCT Module85
Best Practices for the BLM 35/50 System93
Limitations of the BLM 35/50 System94
8 Specification97
Machine Specifications97
- Rotate Crease Trim Module (Option)97
- Booklet Maker98
- Cover Feeder Module99
- Trimmer Module99
- Bookfold Module100
- BST4000-1 Belt Stacker Module100
- System Set Size Guide101
- Cables, Plugs and Jumpers105
Index106

Plockmatic BLM 35 - Page 23

Table of Contents

Related product manuals