RadioLink AT10 User Manual

61
$/22.$77+(5$',26
GLID
-SPECIFIC FUNCTIONS STEP BY STEP.
Those functions which are identical to the
ACRO
setups are referred directly to those pages.
MODEL TYPE
: This function of the
PARAMETER
submenu is used to select the type of model programming to be used.
GLIDER TYPES:
%HIRUHGRLQJDQ\WKLQJHOVHWRVHWXSDJOLGHURUVDLOSODQH¿UVW\RXPXVWGHFLGHZKLFK
MODEL TYPE
EHVW¿WV\RXUDLUFUDIW
•
ACRO
IRUVRPHDHUREDWLFVORSHJOLGHUV
ACRO
is a better choice because of functions it offers that the
GLID
types do not.
•
ACRO
provides:
•
SNAP-ROLL
,
•
AILEVATOR
(twin elevator servo support),
•
AIRBRAKE
(a more assignable version of
BUTTERFLY
).
• For nitro-powered sailplanes:
IDLE-DOWN
,
THR-CUT
,
THROTTLE-NEEDLE
mixing and
THROTTLE DELAY
programming.
• But
ACRO
 ODFNV SURJUDPPLQJ IRU IXOOVSDQ DLOHURQV DQG VHSDUDWH 2))6(7 WULPV IRU HDFK ÀLJKW FRQGLWLRQ 1RUPDO
Start, Speed, Distance and Landing.
•
GLID(1A+1F)
: The
GLID(1A+1F) MODEL TYPE
is intended for sailplanes with one or two aileron servos (or none), and a single
ÀDSVHUYR RU WZRFRQQHFWHG ZLWK D\FRQQHFWRU7KLV
TYPE
is meant to be a very simplistic version to set up a basic
JOLGHUZLWKRXWDORWRIDGGHGIHDWXUHV$GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH
•
GLID(2A+1F)
: The
GLID(2A+1F) MODEL TYPE
LVLQWHQGHGIRUVDLOSODQHVZLWKGXDODLOHURQVHUYRVDQGDVLQJOHÀDSVHUYRRU
WZRFRQQHFWHGZLWKD\FRQQHFWRU$GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH7KHVHÀLJKWFRQGLWLRQVFRQWDLQGLIIHUHQWRIIVHW
trims and aileron differentials to make the sailplane perform certain maneuvers more easily.
•
GLID(2A+2F)
: The
GLID(2A+2F) MODEL TYPE
supports dual flap servos that can also act as ailerons, creating full-span
DLOHURQVDQGÀDSV$GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH7KHVHÀLJKWFRQGLWLRQVFRQWDLQGLIIHUHQWRIIVHWWULPVDQGDLOHURQ
differentials to make the sailplane perform certain maneuvers more easily.
GOAL of EXAMPLE: STEPS: INPUTS:
Change model1 is
MODEL TYPE
to
GLID(1A+1F)
.
NOTE: This is one of the several
functions that the radio requires
FRQ¿UPDWLRQWRPDNHDFKDQJH
Confirm you are currently using the
proper model memory. (Ex: 1)
On home screen, check model nameand
number on top left.
If it is not the correct model (Ex: 1), use
MODEL SELECT
, p. 22.
Open
PARAMETER
submenu.
for 1 second.
(If
ADVANCE
, again.)
C
to
PARAMETER
.
Change the
MODEL TYPE
.
&RQ¿UPWKHFKDQJH
C
to
TYPE
. to
GLID(1A+1F)
.
for one second.
Are you sure?
&RQ¿UPDWLRQGLVSOD\V
WRFRQ¿UP
Close.
GLID(1A+1F)
(FLAPERON)
AIL1
FLP2
(CH1)
AIL2
FLP1
(CH6)
AIL1
(CH1)
AIL2
(CH7)
FLP
(CH6)
GLID(2A+1F)
AIL1
(CH1)
FLP1
(CH6)
FLP2
(CH5)
AIL2
(CH7)
GLID(2A+2F)

RadioLink AT10 Specifications

General

Channels	10
Frequency	2.4GHz
Output Signal	PPM
Control Distance	1.5km
Compatibility	Compatible with most multi-rotor, airplane, helicopter and car models