RadioLink AT10 User Manual

43
There are 4 basic tail types in aircraft models:
• Simple. Model uses one elevator servo and one rudder servo (or multiple servos on a Y-harness). This is the default.
• Dual Elevator servos. Model uses 2 elevator servos. see
AILEVATOR
(
ACRO
) see p. 44.
•
Tail-less model. Model uses 2 wing servos together to create roll and pitch control. see
ELEVON
(
ACRO

GLID 1A+1F
). see p. 43.
•
V-TAIL
. Model uses 2 surfaces, at an angle, together to create yaw and pitch control. see
V-TAIL
(
ACRO

GLID
). see p. 45.
Note: Only one of the three tail-type functions (
AILEVATOR
,
V-TAIL
, and
ELEVON
) can be used at a time. The radio provides a
ZDUQLQJDQGZLOOQRWDOORZWKHDFWLYDWLRQRIDQRWKHUWDLOW\SHXQWLOWKH¿UVWLVGHDFWLYDWHG$QHUURUPHVVDJHRI
OTHER WING
MIXING IS ON
will display. (See the wing type example on page 38.)
Using
ELEVON
(
ACRO

GLID 1A+1F
XVHGZLWKGHOWDZLQJVÀ\LQJZLQJVDQGRWKHUWDLOOHVVDLUFUDIWWKDWFRPELQHDLOHURQDQG
HOHYDWRUIXQFWLRQV XVLQJ WZR VHUYRV RQHRQ HDFKHOHYRQ7KH DLOHURQHOHYDWRUUHVSRQVHV RI HDFK VHUYR FDQEH DGMXVWHG
independently. This is also popular for ground model use, such as tanks, which drive two motors together for forward, and
RQHPRWRUIRUZDUGRQHEDFNZDUGIRUWXUQLQJ
Adjustability:
• Requires use of CH1 and CH2.
• Independently adjustable aileron travel allows aileron differential.
• Independently adjustable elevator travel allows for differences in up vs. down
travel.
• The separate
ELEVON
settings for each condition can be set. (
GLID
only)
[Note] When changing the polarity of a rate, "change rate dir?" is displayed for
a check. Please set up after pressing DIAL for 1 second and canceling an alarm
display. (
GLID
only)
NOTE: If
ELEVON
is active, you cannot activate
FLAPERON
,
AILE-DIFF
, or
AILEVATOR
. An error message
OTHER WING MIXING IS ON
displays and you must
deactivate the last function to activate
ELEVON
.
127(%HVXUHWRPRYHWKHHOHYDWRUDQGDLOHURQVWLFNVWRIXOOGHÀHFWLRQGXULQJ
setup. If large travels are specified, when the AILERON and ELEVATOR
STICKS are moved at the same time the controls may bind or run out of travel.
(GLID 1A+1F)
(ACRO)
(
For details on setting up a complex aerobatic plane, please contact www.radiolink
.com.cn. Many other setup examples are also available at this location.
)
GOAL of EXAMPLE: STEPS: INPUTS:
Activate
ELEVON
.
Adjust aileron down travel to
90%
of up
travel, creating aileron differential.
Open the
ELEVON
function.
for 1 second.
(If
BASIC
, again.)
C
to
ELEVON
.
Activate the function.
C
to
MIX
. to
ACT
.
Optional: adjust the up/down travel
separately for the servos as ailerons.
(Ex: down to
90%
.)
C
to
AIL1
. AILERON STICK.
to
90%
.
C
to
AIL2
. AILERON STICK.
to
90%
.
Optional: adjust the elevator travel of
each servo. (Ex: right servo elev. travel
to
98%
, left to
105%
.)
C
to
ELE2
. to
98%
.
C
to
ELE1
. to
105%
.
Close menu.
Where next? Adjust individual servo's
SUB-TRIMs
: see p. 36 and
END POINTs
: see p. 27.
6HWXSGXDOWULSOHUDWHVDQGH[SRQHQWLDO
D/R
,
EXP
): see p. 30.
View more on the internet: www.radiolink.com.cn/doce/

RadioLink AT10 Specifications

General

Channels	10
Frequency	2.4GHz
Output Signal	PPM
Control Distance	1.5km
Compatibility	Compatible with most multi-rotor, airplane, helicopter and car models