RadioLink AT10 User Manual

65
Adjustability:
• Position: -100% to +100%, with a default of -50% (off), +50% (on)
• Channel: Spoiler 1: ch8, or 3 (ch8 or 3*), Spoiler 2: NULL, or 3 (NULL or ch3*)
*
GLID (2A+2F)
mode
• Elevator setting: Rate: -100% to +100%, Delay: 0% to 100%
• SWITCH A-H fully assignable. Also LOGIC SW (Lsw1 to 3) may be assigned. Set up
LOGIC SW
: See p. 26.
GOAL of EXAMPLE: STEPS: INPUTS:
2-servo spoiler mode.
Adjust the spoiler servo position to
60%
.
Open the
SPOILER MIX
function and
move to 2nd page.
for 1 second. (If
BASIC
, again.)
C
to
SPOILER MIX
.
Activate the function.
C
to
MIX
. to
ON
.
Assign the
SPO2-CH
. (Ex: CH3)
C
to
SPO2-CH
. to
CH3
.
Adjust the spoiler servo position.
(Ex:
SPO1

SPO2
=
+55%
to
+60%
)
C
to
+50%
. (
SPO1
) to
+60%
.
C
to
+50%
. (
SPO2
) to
+60%
.
Optional: Set the elevator rate.
(EX:
10%
)
C
to
rate
-
ELE
. to
10%
.
Optional: Set the delay. (EX:
25%
)
C
to
dly
-
ELE
. to
25%
.
Close menu.
Where next? Set up
BUTTERFLY
mixing: see p. 68.
OFFSETs
DGGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOHVSHFL¿FDOO\IRUVDLOSODQHV
Unnecessary fusulage motion is generated when there are sudden changes in the servo position and variations in the
operating time between channels can be suppressed by using the delay function (
-dly-
).
NOTE: The same delay amount for elevator and rudder is recommended when using V-tail function.
7KH&SURYLGHVRIIVHWWULPVWRDOORZWKHPRGHOHUDGGLWLRQDOVHWXSVDORQJZLWKWKHQRUPDOÀLJKWFRQGLWLRQ
NORMAL
,
START
,
SPEED
,
DISTANCE
and
LANDING
) These offset trims have same setting abilities basically except the switch and dial
assignment. For an example of trim settings, please see the following:
These additional flight conditions contain different offset trims to make the
saiplane perform certain maneuvers more easily. Aileron differential functions
may be set to provide separate rates per condition selected.
Prior to setting up
OFFSET
, you must active the conditions and assign the
switches in the
CONDITION/FUNCTION
.
Adjustability:
6HSDUDWHDGMXVWPHQWVIRUHDFKDLOHURQHOHYDWRUUXGGHUDQGÀDSVHUYRIRUHDFK
condition.
• SWITCH G (AT10) or
E
(AT10) is programmed for
NORMAL
,
START, and SPEED
trims. SWITCH C is programmed for
DISTANCE
and
LANDING
trims. These
VZLWFKSRVLWLRQDVVLJQPHQWLVDGMXVWDEOH
CONDITION/FUNCTION
)
•
TRIM
item (Digital trim operation mode):

RadioLink AT10 Specifications

General

Channels	10
Frequency	2.4GHz
Output Signal	PPM
Control Distance	1.5km
Compatibility	Compatible with most multi-rotor, airplane, helicopter and car models