Raymarine c95 - Page 109

Enablingcentreofview
Toenablethecentreofviewcrosshairatsealevelfollowthesteps
below:
In3Dview:
1.SelectMenu.
2.SelectPresentation.
3.SelectLayers.
4.Select3DDisplayOptions.
5.SelectCentreofViewsothatOnishighlighted.
Selectingcentreofviewwillswitchthecrosshaironandoff.
Adjustingthe3Dchartexaggeration
Inthe3Dchartview:
1.SelectMenu.
2.SelectPresentation.
3.SelectLayers.
4.Select3DDisplayOptions.
5.SelectExaggeration.
6.UsetheRotaryControltoadjusttheexaggerationtothe
requiredsettingbetween1.0and20.0.
Enablingtransducercone
Toenablethetransducerconetoindicatethecoverageofyour
shndertransducerfollowthestepsbelow:
In3Dview:
1.SelectMenu.
2.SelectPresentation.
3.SelectLayers.
4.Select3DDisplayOptions.
5.SelectTransducerConesothatOnishighlighted.
SelectingTransducerconewillswitchthefunctiononandoff.
Enablingdepthscale
Toenableadepthindicatoratyourvesselslocationfollowthesteps
below:
In3Dview:
1.SelectMenu.
2.SelectPresentation.
3.SelectLayers.
4.Select3DDisplayOptions.
5.SelectDepthScalesothatOnishighlighted.
Selectingdepthscalewillswitchdepthindicatoronandoff.
2DChartUse
InadditiontonormalnavigationchartsFishmodeprovides
bathymetriccontourdataonthechartforuseduringshing.
Beforeyoucandisplaybathymetricdatainthechartapplicationyou
musthavechartcardswiththerelevantlevelofdetail.
Whenyouchangethe2DChartUsetotheFishoption,bathymetric
dataisshownonthechart(providingthatthechartcardcontains
bathymetricdataforthatparticularlocation).Certainchartdetailis
alsoremovedtoensurethebathymetricdatacanbeseenclearly
onthechartdisplay.
IfthechartcarddoesNOTcontainbathymetricdatathechart
revertstothedefaultNAV(navigation)data.
Note:Fishmodeisnotsuitablefornavigation.
Selectingshmode
Fromthechartapplication:
1.SelectMenu.
2.SelectPresentation.
3.Select2DChartUsesothatFishishighlighted.
Selecting2DchartusewillswitchthechartbetweenFishand
Navigationmodes.
Multiplechartsynchronization
Youcansynchronizetheheading,range,andpositioninformation
acrossmultiplechartviewsandnetworkeddisplays.
Whenchartsynchronizationisenabled:
•Itisindicatedby“CHRTSync”inthechartapplicationtitlebar.
•Anychangesmadetotheheading,rangeorpositioninanychart
instancewillbereectedinallotherchartinstances.
Note:Whenthe2Dand3Dchartviewsaresynchronized,the
MotionModeisalwaysRelativeMotion.
Synchronizingmultiplechartinstances
Fromthechartapplication:
1.SelectMenu.
2.SelectPresentation.
3.SelectChartSync.
4.SelectChartfromthelist.
Atickisplacednexttotheselectedoption.
5.Repeatthestepsaboveforeachchartinstanceandifrequired
oneachnetworkedmultifunctiondisplayyouwanttosyncthe
chartview.
Note:Youcannotsynctoanotherchartifradarsyncisturnedon.
Usingthechart
109