Regency 4720 - User Manual

100 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

R E G E N C Y

Model 4720 Control/Communicator

Installation Manual

Part Number 150476, Rev. A

Initial Release Date: March 1995

Revised October 1998

Table of Contents

Default Chapter4
- Table of Contents4
Introduction11
- Features11
- Accessories11
Preconnection Requirements12
- Telephone Requirements12
- FCC Requirements13
- UL Installation Requirements13
- Connecting the Supervised Siren Module to the Model 472414
  - NFPA 72 Central Station Signaling and Local Protective Signaling Systems (UL 864)15
- Knockout Plug Installation Diagram16
  - Fire System Test Procedure for UL 985 Systems17
Control Panel Description17
- Regency ® Model 4720 Control/Communicator Installation Manual (P/N 150476, Rev. A) Revised18
- 4720 Printed Circuit Board, Revision L18
- 4720 Printed Circuit Board, Prior to Revision L19
- Battery Connection-PC Boards Prior to Revision L20
- Red LED Indications21
- Model 4720 Non-UL Wiring Diagram27
4720 Control Panel Overview28
- Current Draw Calculations28
  - Total Standby and Alarm Current Draw28
  - Current Draw on Protective Devices Indicated by Leds 2 and 3 (F2 and F3)31
- Current Draw on Protective Devices Leds 2 and 3 (F2 and F3)32
  - System Planning Block Diagram33
- Model 4720 System Planning Diagram33
Wiring Precautions34
Model 4720 Control Panel Installation34
- Selecting a Location34
- Mounting the Model 472035
- Installing the Model 9220 Power Transformer35
  - Model 4165 Transformer Housing35
- Suggested Mounting for the Control Panel35
  - Installing the Transformer36
  - Model 4195 Auxiliary Power Supply37
- Model 9220 Transformer Connection37
Touchpad Installation38
- Mounting the Touchpads38
- Wiring the Model 4195 Auxiliary Power Supply38
Powering up the System41
Internal Zones41
- Mechanical Keyswitch Wiring41
  - Normally Open and Normally Closed Contact Wiring42
  - Smoke Detector Wiring42
- Internal Zone Wiring42
  - Model 7181 Fire Zone Converter43
Local Annunciation43
- Fire Bell Wiring with the Model 4160 Supervised Bell Module43
- ESL 445AT Smoke Detector Wiring43
  - Auxiliary Power for Supervised Bells44
- Model 4160 Supervised Bell Module Wiring44
  - Commercial Burglary Bell Wiring45
- Auxiliary Power for Supervised Bells45
  - External Speaker Wiring46
  - Regency ® Model 4720 Control/Communicator Installation Manual (P/N 150476, Rev. A) Revised46
- Commercial Bell Wiring46
  - Internal Speaker Wiring47
  - Model 4180 Status Relays47
Telephone Line Connection48
- Line 1 Wiring48
- Ground Start Relay Wiring48
- Telephone Line Wiring48
  - External Dialer Failed Indicator49
  - Model 4175 Dual Phone Line Monitor with Ring Detector49
    - Model 4175 Wiring49
- Wiring for External Dialer Failed Indicator49
- Wiring for Model 4175 Dual Phone Line Monitor49
  - Model 4175 Operation50
Expansion Zones50
- Model 4110 Zone Expander50
  - Connecting the Smartsensors50
- Wiring the Model 4110 Serial Zone Expander51
- Wiring the Models 4100 and 4101 Smartsensors51
- Switches to Open to Select Sensor ID Numbers52
- Model 4125 Basic Zone Configurations54
- Wiring the Model 4125 Zone Expander to a 4000 Series Control Panel55
  - Determining 4125 Zone Expander's Input and Zone Numbers56
  - Model 4130 Zone Expander56
    - Installing the Model 413056
    - Programming the Transmitters57
Model 4184 Watchdog Module57
- Model 4184 Watchdog Module Wiring57
- Wiring the Model 4130 RF Zone Expander and Model 4135 Remote Receiver57
  - Operating Procedure, 4184 Watchdog Module58
Other Expansion Devices58
- Model 4140 Intercom/Telephone Controller58
  - Mounting the Model 464059
- Connecting the Model 4140 to the Model 472059
  - Mounting the Model 4640 as a Stand-Alone Intercom60
  - Connecting the Model 4140 to the Model 4640 Intercom Station60
- Model 4640 Audio Module60
- Connecting the Model 464061
- Sample Model 4640 Connection61
  - 7381 Connecting the Model 4140 to the Model 7381 Front Door Intercom Station62
- Wiring Table62
- Connecting the Model 7381 to the Model 414062
- Model 7367 with Speaker and Supplied Microphone63
  - Model 7369 Two-Way Audio Listen-In Module64
- Model 7367 with Model 4640 Speaker and Microphone64
Touchpad Operation65
- Model 4660B/C Commercial Touchpad65
- Model 4660R Residential Touchpad65
Touchpad Functions69
- Viewing Status69
- Silencing Troubles69
- Bypassing Zones69
- Alarm Memory69
  - To Display Alarm Memory69
  - To Clear Memory70
- Chime Function70
- Interior Function70
- Panic Keys70
- Resetting an Alarm70
- Signaling Duress70
- Door Access70
  - DOOR Key (Commercial Touchpads Only)70
  - CODE 2 Key (Code 2 Residential Touchpads Only)71
    - To Enable Code 271
    - To Disable Code 271
- 4150 Relay Access71
- Test Modes71
- Intercom Operation73
- Telephone74
  - Basic Operation74
  - Memory Dialing74
    - Entering Phone Numbers into Memory74
    - Dialing Phone Numbers in Memory74
Preprogrammed EEPROM75
- Factory-Programmed Options75
- Reprogramming the EEPROM76
Programming77
- Model 4720 Downloading (with 5540 PC Downloading Software)77
- Model 5520 Field Programmer78
- Model 5520 Programmer Menus78
Touchpad Programming79
Area Control Operation80
Model 4720 Reporting Formats80
SIA Reporting Format82
Trouble/Error Messages84
- Troubles84
- Errors85
Troubleshooting85
New Features Available with Revision N of the Model 472086
- Sprinkler Supervisory Zone Type86
- Wiring Sprinkler Supervisory Zones86
  - LCD Operational Changes87
  - Memory Reporting During Auto Test87
Regency ® One Year Limited Warranty88

Need help?

Do you have a question about the Regency 4720 and is the answer not in the manual?

Summary

Preconnection Requirements for Installation

Telephone Line Requirements

Specifies information required by the telephone company and restrictions for connecting the device.

Control Panel Description and Components

Battery Cables and Power Connections

Details the connection of battery cables for backup power and the DC power switch.

Model 4720 Control Panel Installation Guide

Selecting an Optimal Location for the Panel

Provides factors to consider when choosing a mounting location for the control panel.

Mounting and Transformer Installation Procedures

Details how to mount the control panel and install the power transformer.

Touchpad Installation Procedures

Mounting Touchpad Devices

Step-by-step instructions for physically mounting the touchpads to a wall.

Wiring the Touchpads to the Control Panel

Details the wiring connections required for touchpads and daisy-chaining.

Setting Touchpad ID Codes

Procedure for assigning unique ID numbers to each touchpad in the system.

Internal Zone Wiring and Configuration

Contact Wiring Methods for Internal Zones

Explains wiring for normally open, normally closed, and supervised contacts.

Wiring Smoke Detectors to Internal Zones

Details the connection of ESL 445AT smoke detectors and related components.

Local Annunciation Methods

Fire Bell Wiring with Supervised Bell Module

Instructions for wiring fire bells using the Model 4160 supervised bell module.

Telephone Line Connection and Monitoring

Basic Line 1 Wiring and Ground Start

Expansion Zones and Sensor Configuration

Model 4110 Zone Expander Installation

Determining Zone Expander ID and Zone Numbers

Model 4125 Multiplexed Zone Expander Wiring

Touchpad Operation and Functions

Advanced Touchpad Functions

Alarm Memory and Door Access Operations

Test Modes and System Operations

Model 4720 Reporting Formats

SIA (Security Industry Association) Format

Trouble and Error Messages

Trouble Messages and Their Meanings

Lists common trouble messages like PAPER, DATA LOST, FAILED, BATTERY, AC, LINE issues.

Error Messages and System Restrictions

Explains error messages such as TRY AGAIN, RESTRICTED CODE, ZONE, and TIME.

Troubleshooting Common Issues

Regency 4720 Specifications

General

Brand	Regency
Model	4720
Category	Cell Phone
Language	English